Leadshine Technology DM870 User Manual Download Page 17

                                 

DM870 Microstepping Driver Manual V1.0

 

Tel: +086 0755-26434369                                29                                  Web Site: www.leadshine.com 

APPENDIX 

Twelve Month Limited Warranty   

Leadshine  Technology  Co.,  Ltd.  warrants  its  products  against  defects  in  materials  and 
workmanship for a period of 12 months from shipment

 

out of factory. During the warranty period, 

Leadshine will either, at its option, repair or replace products which proved to be defective. 

Exclusions                                                                                                                           

The above warranty does not extend to any product damaged by reasons of improper or inadequate 
handlings  by  customer,  improper  or  inadequate  customer  wirings,  unauthorized  modification  or 
misuse,  or  operation  beyond  the  electrical  specifications  of  the  product  and/or  operation  beyond 
environmental specifications for the product. 

Obtaining Warranty Service                                                                                     

To  obtain  warranty  service,  a  returned  material  authorization  number  (RMA)  must  be  obtained 
from  customer  service  at  e-mail: 

[email protected]

  before  returning  product  for  service. 

Customer  shall  prepay  shipping  charges  for  products  returned to  Leadshine  for  warranty  service, 
and Leadshine shall pay for return of products to customer.   

Warranty Limitations                                                                             

Leadshine  makes  no  other  warranty,  either  expressed  or  implied,  with  respect  to  the  product. 
Leadshine  specifically  disclaims  the  implied  warranties  of  merchantability  and  fitness  for  a 
particular purpose. Some jurisdictions do not allow limitations on how long and implied warranty 
lasts, so the above limitation or exclusion may not apply to you. However, any implied warranty of 
merchantability or fitness is limited to the 12-month duration of this written warranty. 

Shipping Failed Product         

                                                                                           

If your product fail during the warranty period, e-mail customer service at 

[email protected]

 to 

obtain  a  returned  material  authorization  number  (RMA)  before  returning  product  for  service. 

Please  include  a  written  description  of  the  problem  along  with  contact  name  and  address.  Send 

failed product to distributor in your area or: Leadshine Technology Co., Ltd. 3/F, Block 2, Nanyou 

Tianan  Industrial  Park,  Nanshan  Dist,  Shenzhen,  China.  Also  enclose  information  regarding  the 

circumstances prior to product failure. 

 

                               

DM870 Digital Stepping Driver Manual V1.0

 

Tel: +086 0755-26434369                                30                                  Web Site: www.leadshine.com 

Contact Us 

China Headquarters

 

Address:

 3/F, Block 2, Nanyou Tianan Industrial Park, Nanshan District Shenzhen, China 

Web:

 

http://www.leadshine.com

 

Sales Hot Line:

 

Tel:

 86-755-2643 4369 (for All) 

86-755-2641-7674 (for Asia, Australia, Africa areas) 

86-755-2640-9254 (for Europe, America areas) 

Fax:

 86-755-2640-2718 

Email:

 

[email protected]

Technical Support:

 

Tel:

 86 755-2641-8447 and 86-755-2647-1129 

Fax:

 86-755-2640-2718 

Email:

 

[email protected]

 and 

[email protected]

Leadshine U.S.A

 

Address:

 25 Mauchly, Suite 318 Irvine, California 92618 

Tel:

 1-949-608-7270 

Fax:

 1-949-608-7298 

Web:

 http://www.leadshineUSA.com 

Email:

 

[email protected]

 and 

[email protected]

Leadshine Hong Kong

 

Address:

 Rm 3, 9/F, Block E, Wah Lok Industrial Center,31-41 Shan Mei St., Fo Tan, 

Shatin, Hong Kong 

Tel:

 852-2952-9114 

Fax:

 852-2952-9395 

Email:

 

[email protected]

Summary of Contents for DM870


















Reviews: