background image

LOADING

: First insert the double-sided lifting cup (PAP 1220) by pushing

it down the barrel to the bottom, using the ramrod provided.  You may need
to squeeze in the bottom side of the cup to make the lower end fit.  This
cup acts as a bottom expanding propellant sealer and helps eject your
streamers further.  Note: Be sure the cup is inserted fully down the barrel
onto the stop.
Now you are ready to load in streamers and/or confetti effects on top of the
cup.  Hard press packing is not necessary but you may compress, a little.

                              

 We recommend 4 sleeves of 18 ft. streamers or 3

sleeves of 25 ft. streamers. More or less can be used, however, the more
you use, the more spectacular the effect!  If your budget permits, a full
barrel looks unbelievable but you do not need to fill barrel to get a great
effect.

LOADING TIP

: If you are mixing big streamers with small streamers, load

in the smaller streamers first, on up to the largest.  For the best visual
effect, shoot in an 18’ or higher area with mortar set at a 45-degree angle.
Results are not as effective in a low ceiling environment.

                           We recommend 12 Stacks
of Profetti per load. Please see diagram for
suggested loading method. By loading the
Profetti in a cross pattern we create some
friction on the sides of the launcher barrel,
this will help in launching the Profetti in the
air.

INSTALLING THE BACKPRESSURE CAP

(PAP 1210)  Slip the cap over and the end of the barrel and snug it down.
With masking tape, neatly tape 2 or 3 turns around the side of the barrel
and cap.  After taping, roll your hand around the tape, pressing to form a
tight air seal.  When firing, backpressure will be increased, thus blowing
the lid off and expelling the contents.  Note: The lifting cups are reusable if
you can find them, however, the backpressure caps may need replacing if
they tear when blown off.

4

IMPORTANT

: Firing pin must have movement after Co2 has been installed.

If not, you should screw out Co2 cylinder by one or two turns.  You can
avoid this issue by using Le Maitre CO2 cartridges (PAP 1200)

Summary of Contents for PRO LAUNCHER











Reviews: