background image

Page 7

v.06.18.20

LDPI, Inc.   |   (800)-854-0021   |   www.ldpi-inc.com   |   [email protected]

SERVICING / WARRANTY

LEHL2

Servicing

- To avoid personal injury, disconnect power to the light and allow the unit to cool down before performing maintenance.

- Perform visual, electrical, and mechanical inspections on a regular basis. The environment and frequency of use will determine

   how often. However, it is recommended that inspections occur annually.

- The external lens should be cleaned periodically to ensure continued luminaire performance. Clean the lens with a clean, damp,

   non-abrasive, lint-free cloth. If this is not sufficient, use a mild soap or a liquid cleaner. Do not use an abrasive, strong alkaline or

   acid cleaner as damage may occur.

- Inspect the cooling fins of the luminaire to ensure that they are free of any contamination (i.e. excessive dust build-up). Clean

   with a non-abrasive cloth if needed.

- Check all moving parts and components to ensure they are properly assembled and in good operating order.

- Check all electrical connections to ensure all connections are clean and tight.

Warranty

We warrant that each of our LED lighting luminaire (the “Product(s)”) that are purchased while this Warranty is in effect will be free 

from defects in materials and workmanship for the period of time specified in the table below (the “Warranty Period”). The Warranty 

Period runs from the date of original purchase from its authorized distributor/dealer.

We will repair, or at our option, replace the defective product (exterior finish, housing and heat sinks, lens, LED engine, power supply) 

during the standard warranty period. This warranty applies only to the repair or replacement of the product and only when the product 

is properly handled, installed and maintained according to our instructions.

 

This warranty excludes defects resulting from improper installation, acts of God, fire, vandalism or civil disturbances, power surges or 

improper power supply, and corrosive environment installations. 

 

This warranty does not cover equipment, systems or components from other manufacturers that the Purchaser uses in conjunction 

with the Product. Any repair, alteration or modification of the Product, including replacement of Product components with components 

of other manufacturers will void the warranty in its entirety.

Explosion Protected LED Luminaire 

LEHL2 Series

5 Years

Product

Model Nos. Covered

under this Warranty

Warranty

Period

Summary of Contents for LEHL2 Series








Reviews: