manualshive.com logo in svg

LCI Wyvern 2000N, Handbook, Page: 11 / 16

Share
Download
LCI Wyvern 2000N Handbook Download Page 11

Wyvern

®

2000N Banknote Timer  Handbook      9

Interrogation Menu

The interrogation menu gives access to various audit functions. To access the

interrogation menu press and hold both UP and DOWN buttons for approximately
5 seconds. Press and release the UP button to access the interrogation number
required. To leave interrogation mode press and hold both UP and DOWN buttons
for approximately 5 seconds. Audit functions are non resettable.

Sessions - Audit Function 1

Audit function 1 displays the total number of sessions that have been activated

since build.

Minutes - Audit Function 2

Audit function 2 displays the total number of minutes that the Wyvern

®

2000N has

counted down - i.e. the total time the load has been operated.

Total - Audit Function 3

Audit function 3 displays the total number of minutes that the Wyvern

®

2000N has

been active. This includes total pre-time and cool down time as well as count
down time. If pre-time and cool down time options have been set to zero then
audit functions 2 and 3 will be identical

Currency Total - Audit Function 4

Audit function 4 is selected with audit code c- and shows the total

currency accumulated for accepted notes. When trailing zeros have been
removed when programming currency values (for example $500 note
programmed as 50) then the currency total must be multiplied by the
correct factor. Selecting this function clears “Err4” (page 10).

Audit Code

Description

Maximum

Comments

1-

Session

65535

Audit Code

Description

Maximum

Comments

2-

Minutes

65535

Audit Code

Description

Maximum

Comments

3-

Total

65535

Audit Code

Description

Maximum

Comments

c-

Currency Total (CT)

999999

Summary of Contents for Wyvern 2000N

















Reviews:

No comments