LBC LRP Operator'S Manual Download Page 30

Page: 30 / 32

Page | 30 Proofer Operators Manual 1-2022 (English)

Retarder/Proofer control

Function settings

Function Short Name

Description

Factory

set point

Range

Temperature
Calibration

Increase the value to increase the display and lower the
actual temperature.

+25, -25

Humidity
Calibration

Increase the value to increase the display and lower the
actual humidity.

+25, -25

Temperature Lock

Limit the range of temperature variance shown in degrees.

0 - 9

Humidity Lock

Limit the range of humidity variance shown in degrees.

0 - 9

Heat PID range

Sets the range for PID control in degrees.

0 - 99

Proportion Factor

Sets the ratio of proportional off/on time to temperature
difference.

0 - 30

Heat cycle time

Sets the length of the PID cycle in seconds.

1 - 99

Humidity Cycle
time

Sets the length of time in seconds for each humidity cycle.

1 - 99

Humidity On time

Sets the "on" time in seconds for humidity in each cycle.

0 - 20

F10

Refrigeration Defer
time

Sets how long the control will delay the turning on of the
cooling system in minutes.

0.0

0.0 - 9.9

F11

Cooling Dead Band

Temperature difference between cooling off and cooling on.

2.0

0.0 - 9.9

F12

Heating Dead Band

Temperature difference between heating on and heating off.

0.5

0.0 - 9.9

F13

Not used

Set to 0.5

005

0 - 9

F14

Light on time

How long the light will be on in seconds. "0.0" = light will be
on indefinitely.

0.5

0.0 - 9.9

F15

Alarm on time

Determines how long the alarm will sound before it turns off,
in seconds. "0.0" means the alarm will stay on indefinitely.

0.0

0.0 - 9.9

F16

Defrost time

Length of the defrost time in minutes. "00" = no defrost.

0.0 - 9.9

F17

Defrost delay

Determines how long between starts of the defrost cycle in
hours. "00" = no defrost.

0.0 - 9.9

F18

Defrost
Temperature

Determines what temperature ends the defrost cycle, when
a thermistor is imbedded in the evaporator.

00 - 200

Summary of Contents for LRP




























Search results

Summary of Contents for LRP

Reviews:

Related manuals for LRP

Brands by name

Popular brands

LBC LRP, Operator'S Manual

Search results

Summary of Contents for LRP

Reviews:

Related manuals for LRP

Brands by name

Popular brands