LAWO V_pro8 Installation & Operation Manual Download Page 93

Page: 93 / 109

V_pro8 Manual

V1.0/2

Operation (Web Browser Control)
Timing

Ref Out

This sub menu selects options for the

video reference output

on the

pro8

's rear panel:

Two different

Ref Out Mode

s are available:

Follow Genlock

- the video output follows the Master Genlock.

Selectable

- click on

Ref Out Format

to select the video output format; black buttons can be

selected; grey buttons cannot (as they are not supported by the current video reference). In
our example, we can select any 50Hz format or derivatives such as 1080 25p:

You can change which output format options are black (selectable) by changing the

Video

Reference

and/or

Format

field in the

Timing -> Timing Pos

menu.

Summary of Contents for V_pro8














































































































Search results

Summary of Contents for V_pro8

Reviews:

Related manuals for V_pro8

Brands by name

Popular brands

LAWO V_pro8, Installation & Operation Manual

Search results

Summary of Contents for V_pro8

Reviews:

Related manuals for V_pro8

Brands by name

Popular brands