background image

17

Avoid direct skin contact with petrol and the inhalation of petrol fumes. 
Health hazard!

The equipment is fitted with a two-stroke engine and therefore 
operated exclusively with a mix of petrol and two-stroke engine 
oil in the ratio 50:1.

•   Use quality unleaded petrol with an octane rating of at least 91.
•   Optimum performance will be achieved with the use of high quality two-stroke engine oil 
    (FC class) designed specifically for the equipment. If this is not available, use super oil for 

    air-cooled two-stroke engines.

1. Mix petrol and oil in the fuel mixing can (27) included in the delivery: Fill with petrol (gas) up 
    to the “588.36” mark. Fill with two-stroke engine oil (oil) up to the “1:50” mark. Close the 

    container and shake carefully.

2. Unscrew the tank cap (37) and pour the fuel mix into the fuel tank (2). Wipe away fuel residues 

    around the tank cap and reclose the tank cap.

Filling with Fuel (Picture 8):

 

Always ensure good ventilation when handling fuel.
Do not smoke when filling with fuel and keep away from any heat sources. 
Never fill with fuel when the engine is running. Open the tank cap carefully, 
so any excess pressure present can be relieved slowly. Start the equipment 
min. 3 m away from the fuel filling location. Risk of fire or explosion in case 
of non-observance.

Use only the fuel mix recommended in the instructions. The fuel mix 
deteriorates over time. Therefore, do not use fuel mix that is older than 3 
months. In case of non-observance, the engine can be damaged and the 
guarantee will be invalidated.

 

pic  8

2

37

Summary of Contents for FW35E




































Reviews: