Lava Aire Fantom User Manual Download Page 3

 

2. 

Continuous water supply 

 

 

 

 

 

 

 

 

 

 

 

 

3. 

 

1. Take out rubber cover from the water inlet. 

2. Connect one end of water pipe to the base. (Internal diameter of pipe is 15mm) 

3. Connect another end of water pipe to the tap, and then open the tap. 

Note: 

Do not add dirty water or any additives (such as perfume, essential oil and mosquito repel, etc.), instead add 

clean drinking water or purified water to ensure longer life of the humidifier. 

 

 Operating the Fan

  

 

 

 

 

 

 

 

 

 

 

 

 

Insert plug to the electrical outlet, and then turn on each switch to operate above functions. 

1. Turn on speed switch, to choose the wind speed - Low, Med, High. 

2. Pull down oscillation switch, to change the wind direction. Pull up this button again to stop oscillation. 

3. Turn on mist switch, the mist will spread out from the mist spray hole, “MIST” function can be used together with or 

independently of the fan. If the mist function is used separately, it can increase humidity level in the air. 

 

 

Safety Precaution

  

 

1. Make sure this appliance and the power cord is not damaged before operating. In case of damage, please send the unit  

to the  authorized technical service center. 

2. Do not unplug the unit from the electrical outlet with wet hands. 

3. Do not touch the electrical wirings and water in the tank if the unit is turned on. 

4. Do not insert any object into guard and mist spray hole to avoid destroying the unit. 

5. Unplug the unit from the electrical outlet when not operating and before moving, installing, uninstalling and cleaning the 

unit.  

6. Do not pull the plug while the power is on. Always ensure that the plug is fully inserted into the electrical outlet before 

operating. 

7. Do not add any chemical, metal ingredient into the water tank or flume, as these materials are dangerous and may 

cause problems. 

8. Automatic switch shall be cut off when water in the tank is not enough. This is to protect the ultrasonic transducer. Add 

more water to allow continuous use. 

9. This appliance must be used under the rated voltage and frequency as indicated in rating label. 

10. Do not disassemble, repair or modify this appliance on your own or send the unit for repair to an unauthorized person 

as warranty will be void. 

11. If the power cord is damaged, it must be replaced immediately by the service center to avoid electrical hazard. 

12.  This  appliance  is  not  intended  for  use  by  persons  (including  children)  with  reduce  physical,  sensory  or  mental 

capabilities, or lack of experience and knowledge. With proper supervision or instruction concerning use of the appliance 

by a person responsible for their safety, they may operate it otherwise.  

13.  Children should be supervised to ensure that they do not play with the appliance. 

 

 

 

Summary of Contents for Fantom

Page 1: ...nt Working Principle The Ultrasonic mist fan uses supersonic concussive elements that atomize water down to 1 5 micron ultra particles and through the industrial fan it spreads the ultrasonic mist into the air and thus cooling down the room temperature 1 Front grille guard ornament 2 Front guard 3 Blade cap 4 Blade 5 Guard mounting nut 6 Rear guard 7 Motor 8 Iron tube upper 9 Iron tube connector 1...

Page 2: ...ar guard tightly by turning the guard mounting nut clockwise Assembly of fan blade 1 Insert the blade to the motor shaft and ensure the pin enters the blade slot 2 Tighten the blade using the blade cap turning it counter clockwise in the direction with a TIGHT arrow indicated on it Note Proper assembly of the blade is of great importance Otherwise the blade spins out of direction and can cause dam...

Page 3: ...he tank if the unit is turned on 4 Do not insert any object into guard and mist spray hole to avoid destroying the unit 5 Unplug the unit from the electrical outlet when not operating and before moving installing uninstalling and cleaning the unit 6 Do not pull the plug while the power is on Always ensure that the plug is fully inserted into the electrical outlet before operating 7 Do not add any ...

Page 4: ...e a new water tank b Change a new fan motor 3 Why is there no mist even though fan is working a No water or water level is not enough b Bobber doesn t float in the water c Ultrasonic transducer surface was filled up d Clamp plate of water level switch is not firmly positioned in place e Ultrasonic transducer is damaged a Add water b Pull out the bobber and let it float out c Clean ultrasonic trans...

Reviews: