Lattice ECP2 Series Usage Manual Download | Manualshive

Page: 10 / 33

background image

15-10

LatticeECP2/M sysCONFIG Usage Guide

The estimated time for configuration can be calculated by dividing the bitstream size (in bits) from Table 15-4 by the
CCLK frequency. The CCLK frequency can be set using the global preferences tab within the ispLEVER Design
Planner or the Spreadsheet View (Global Preferences tab) in Diamond. For more information on setting the CCLK
frequency, please see the Master Clock section and the D[0]/SPIFASTN pin section of this document.

When downloading an encrypted bitstream file to the LatticeECP2/M S-Series devices, the user must adhere to the
appropriate conditions for the CCLK signal. These conditions are shown in TN1109,

LatticeECP2/M Configuration

Encryption Usage Guide

Table 15-6. SPI Serial Flash Vendor List

One FPGA, One SPI Flash

The simplest SPI configuration consists of one SPI Serial Flash connected to one LatticeECP2/M, as shown in
Figure 15-1. This is also the recommended method for use when downloading an encrypted bitstream file to the
LatticeECP2/M S-Series devices.

Figure 15-1. One FPGA, One SPI Serial Flash

Multiple FPGA, One SPI Flash

With a sufficiently large SPI Flash multiple FPGAs can be configured as shown in Figure 15-2. The first FPGA is
configured in SPI mode; the following FPGAs are configured in Slave Serial mode.

Vendor

Part Number

ST Microelectronics

M25Pxx

Winbond

W25Pxx

Silicon Storage Technology

SST25VFxx,

SST25LFxx

Spansion

S25FLxx

Atmel

AT25Fxx

NexFlash

NX25Pxx

Macronix MX25Lxx

Note: This is not meant to be an exhaustive list and may be updated
from time to time.

Lattice FPGA

SPI Mode

CCLK

DI/CSSPI0N

BUSY/SISPI

D7/SPID0

DOUT

CFG1

CFG0

SPIFASTN

SPI Serial

Flash

Q

C

CFG2

D0/SPIFASTN

PROGRAMN

DONE

D

/CS

«
...
8
9
10
11
12
...
»

Summary of Contents for ECP2 Series


































Reviews:

No comments

Related manuals for ECP2 Series

Brand: GAUGEMASTER Pages: 2

Brand: EasyIO Pages: 19

Brand: PAC Pages: 17

ROBO Cylinder RCP2 Series

Brand: IAI Pages: 5

Brand: Magnescale Pages: 3

Brand: Zamel Pages: 2

Brand: D+H Pages: 32

Brand: Data Signs Pages: 23

WFHC 06Z 02 HC RF 24

Brand: Watts Pages: 18

Errata MSP430F6779

Brand: Texas Instruments Pages: 27

Brand: OLYS Pages: 4

The Boost Box WS 1107

Brand: Watersports Innovations Pages: 12

Brand: Parker Pages: 31

Brand: Rauch Pages: 85

CC2530-CC2592EM

Brand: Texas Instruments Pages: 3

Brand: Samson Pages: 130

Brand: Eaton Pages: 10

Brand: Go Power Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands