Lattice Semiconductor OpenLDI/FPD-LINK/LVDS User Manual Download Page 5 | Manualshive

Page: 5 / 45

background image

OpenLDI/FPD-LINK/LVDS Receiver Interface IP

User Guide

© 2017-2019 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at

www.latticesemi.com/legal

All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

FPGA-IPUG-02021-1.1

5

Introduction

The Lattice Semiconductor OpenLDI/FPD-LINK/LVDS Receiver Interface IP translates video streams from a processor
with an OpenLDI/FDP-Link/LVDS interface connection to pixel clock domain. This can be used to connect with other
application interfaces, such as the Mobile Industry Processor Interface (MIPI

®

) Display Serial Interface (DSI) by

integrating it with Pixel-to-Byte Converter and CSI-2/DSI D-PHY Transmitter Submodule IPs.

The increasing demand for better displays makes bridging applications very popular. The Flat Panel Display Link
(FPD-Link) is a common application interface. Applications such as Channel Link, FPD-Link, and Camera Link use LVDS
interface for physical layer.

The Low Voltage Differential Signaling (LVDS) standard is commonly used for high-speed differential interface in
consumer devices, industrial control, medical, and automotive. The LVDS interface offers low voltage, low power and
improved signal integrity advantages over single-ended technology.

The 7:1 LVDS interface is a popular standard for source synchronous interfaces which consist of multiple data bits and
clocks. Typically, 1 channel of 7:1 LVDS interface consists of five LVDS pairs (1 clock and 4 data) depending on the data
type it supports.

This document describes the use of Lattice FPGA technology for applications requiring LVDS interface and how to use
the IP. This design can be used in multiple configurations.

This document is for OpenLDI/FPD-LINK/LVDS Receiver Interface IP design version 1.x.

Application

Processor

DCK0

MIPI DSI

LVDS

DCK0
D[0:3]

D0-D3

DCK1
D[4:7]

DCK1
D4-D7

Figure 1.1. Sample OpenLDI/FPD-LINK/LVDS Receiver interfaced to MIPI DSI System Diagram

1.1.

Quick Facts

provides quick facts about the OpenLDI/FPD-LINK/LVDS Receiver Interface IP for CrossLink™ device.

Table 1.1. OpenLDI/FPD-LINK/LVDS Receiver Interface IP Quick Facts

OpenLDI/FPD-LINK/LVDS Receiver Interface IP Configuration

1x7 Rx, RGB888

Configuration

2x7 Rx, RGB888

Configuration

1x14 Rx, RGB888

Configuration

2x14 Rx, RGB888

Configuration

IP
Requirements

FPGA Families
Supported

CrossLink

Resource
Utilization

Targeted Device

LIF-MD6000-6MG81I

Data Path Width

28-bit input,

parallel output

56-bit input (28-bit

per Rx channel),

parallel output

28-bit input,

parallel output

56-bit input (28-bit

per Rx channel),

parallel output

LUTs

233

237

318

390

sysMEM™ EBRs

0

0

0

0

Registers

119

143

176

248

HW MIPI Block

0

0

0

0

Programmable
I/O

34

62

58

110

Design Tool
Support

Lattice
Implementation

Lattice Diamond

®

3.9

Synthesis

Lattice Synthesis Engine

Synplify Pro

®

L-2016.09L

Simulation

Aldec

®

Active HDL™ 10.3 Lattice Edition

«
...
3
4
5
6
7
...
»

Summary of Contents for OpenLDI/FPD-LINK/LVDS














































Reviews:

No comments

Related manuals for OpenLDI/FPD-LINK/LVDS

Brand: 3M Pages: 2

Brand: Raymarine Pages: 24

Brand: Hansen Pages: 72

Brand: AAT Pages: 16

Brand: AAT Pages: 40

Platinum Series

Brand: Dairy Tech Pages: 38

Brand: H&S Pages: 34

Brand: QAL Medical Pages: 42

Brand: Gaspardo Pages: 196

Brand: RAB Pages: 2

Brand: NEILPRYDE Pages: 55

Brand: HANYOUNGNUX Pages: 4

Brand: Park House Healthcare Pages: 6

Brand: J&M Pages: 33

Brand: Kamikaze Pages: 112

Brand: KAM Pages: 2

Brand: TC Electronic Pages: 67

Brand: Tascam Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands