Lattice Semiconductor OpenLDI/FPD-LINK/LVDS User Manual Download Page 32 | Manualshive

Page: 32 / 45

background image

OpenLDI/FPD-LINK/LVDS Receiver Interface IP

User Guide

© 2017-2019 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at

www.latticesemi.com/legal

All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

32

FPGA-IPUG-02021-1.1

IP Generation and Evaluation

This section provides information on how to generate the Lattice OpenLDI/FPD-LINK/LVDS Receiver Interface IP code
using the Lattice Diamond Clarity Designer and how to run simulation, synthesis and hardware evaluation.

5.1.

Licensing the IP

The OpenLDI/FPD-LINK/LVDS Receiver Interface IP is available free of charge, but an IP-specific license is required to
enable full, unrestricted use of the OpenLDI/FPD-LINK/LVDS Receiver Interface IP in a complete, top level design.

Request your license by going to the link

http://www.latticesemi.com/en/Support/Licensing

and request the free

Lattice Diamond license. In this form, select the desired CrossLink IP for your design.

You may download and generate the OpenLDI/FPD-LINK/LVDS Receiver Interface IP and fully evaluate the IP through
functional simulation and implementation (synthesis, map, place and route) without an IP license.

The OpenLDI/FPD-LINK/LVDS Receiver Interface IP also supports Lattice’s IP hardware evaluation capability, see the

Hardware Evaluation

section further details.

HOWEVER, THE IP LICENSE IS REQUIRED TO ENABLE TIMING SIMULATION, TO OPEN THE DESIGN IN DIAMOND EPIC
TOOL, OR TO GENERATE BITSTREAMS THAT DO NOT INCLUDE THE HARDWARE EVALUATION TIMEOUT LIMITATION.

5.2.

Getting Started

The OpenLDI/FPD-LINK/LVDS Receiver Interface IP is available for download from the Lattice IP Server using the Clarity
Designer tool. The IP files are automatically installed using ispUPDATE technology in any customer-specified directory.
After the IP has been installed, the IP is available in the Clarity Designer user interface as shown in

Figure 5.1. Clarity Designer Window

«
...
30
31
32
33
34
...
»

Summary of Contents for OpenLDI/FPD-LINK/LVDS














































Reviews:

No comments

Related manuals for OpenLDI/FPD-LINK/LVDS

Brand: T-Drill Pages: 75

Brand: Zeiss Pages: 38

Brand: AcceleDent Pages: 3

Brand: Zero 88 Pages: 32

Brand: Vahle Pages: 96

Brand: Fenton Pages: 16

Brand: Additel Pages: 107

Brand: Vag Pages: 10

Cell Saver Elite+

Brand: Haemonetics Pages: 230

Pro hunter 2525

Brand: SprotDog Pages: 28

Brand: Metrohm Pages: 42

Brand: Maquet Pages: 232

Brand: Kitagawa Pages: 32

Brand: American DJ Pages: 8

Brand: COURANT Pages: 2

Brand: laerdal Pages: 64

Brand: Proceq Pages: 35

Brand: Game Winner Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands