background image

MachXO5-NX Development Board 
Preliminary Evaluation Board User Guide 

© 2022 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at 

www.latticesemi.com/legal

 

All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 

14 

 

FPGA-EB-02052-0.90 

The MachXO5-NX Development Board also provides test points for other dedicated JTAG configuration pins as shown 
in 

Table 3.2

 

Table 3.2. Other Config JTAG Control Signals 

Net Name  

MachXO5-25 Ball Location 

LED Indicator 

Test Point 

JTAGEN 

B20 

— 

Pin 1 of JP2 

PROGRAMN 

F12 

— 

Pin 1 of JP5 

INITN 

E13 

D11 

TP5 

DONE 

F13 

D10 

TP6 

 

JP2 for JTAGEN is used to pull down the JTAGEN for enabling JTAG port when JTAG_PORT is disabled by software. JP5 
can bridge push button PB4 with PROGRAMN when PROGRAMN_PORT function is enabled by software. 

3.2.

 

I

2

C Download Interface 

The USB hub on the PC can also detect the addition of the USB function on Config FTDI Port B and you can select the 
port FTUSB-1 on the programmer interface for the accessing from Config FTDI Port B to the MachXO5-25 dedicated I

2

download port (

Figure 3.2

) that is named as FTDI_SDA/FTDI_SCL with 2.2 kΩ pull up resistor each. The Diode D21 is 

inserted to support I

2

C

 

clock stretching mode. Figure 3.5

 

details the design of Config FTDI Port B for dedicated I

2

download interface. Table 3.3 summarizes the interconnection with MachXO5-25 and its supported circuits. JP12 and 
JP13 are used to connect the dedicated I

2

C download port of MachXO5-25 with the bridge I

2

C bus SDA0/SCL0 cross the 

whole board, in case you need access I

2

C download port from other on board headers other than Config FTDI part. For 

the detail connection from other headers to bridge I

2

C bus SDA0/SCL0, refer to th

User I2C Interface

 section. 

 

Figure 3.5. I

2

C Programming Mode 

Table 3.3. Download I

2

C Connections 

Download I

2

C Net Name 

MachXO5-25 Ball 

Location for JTAG 

2.2 kΩ Pull up Resistor 

Bridge I

2

C Net 

Name 

Bridge Jumper 

FTDI_SCL 

G15 

R33 

SCL0 

JP12 

FTDI_SDA 

F15 

R34 

SDA0 

JP13 

 

For more information on MachXO5-25 JTAG/ I

2

C programming, refer to MachXO5-NX Programming and Configuration 

User Guide (FPGA-TN-02271)

.

 

 

Summary of Contents for MachXO5-NX Development Kit

































































Reviews: