background image

Programming Cables  

User Guide 

© 2009-2019 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at 

www.latticesemi.com/legal

 

All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 

FPGA-UG-02042-26.2 

 

19 

Revision 24.9, October 2015 

Section 

Change Summary 

Programming Flywire and 
Connection Reference 

Revised Table 3, Recommended Pin Connections.  

 

Added CRESET-B column.  

 

Added iCE40 UltraLite device. 

Technical Support Assistance 

Updated Technical Support Assistance information. 

 

Revision 24.8, March 2015 

Section 

Change Summary 

Programming Cable Pin 
Definitions 

Revised description of INIT in Table 1, Programming Cable Pin Definitions. 

 

Revision 24.7, January 2015 

Section 

Change Summary 

Programming Cable Pin 
Definitions 

 

In Table 1, Programming Cable Pin Definitions, ispEN/Enable/PROG changed to 
ispEN/Enable/PROG/SN and its description revised. 

 

Updated Figure 2, Programming Cable In-System Programming Interface for the PC 
(HW-USBN-2B). 

Programming Cable ispEN Pin 

In Table 4, Programming Cable Feature Summary, HW-USBN-2B marked as available for 
order. 

Ordering Information 

HW-USBN-2A changed to HW- USBN-2B. 

 

Revision 24.6, July 2014 

Section 

Change Summary 

All 

Changed document title from ispDOWNLOAD Cables to Programming Cables User’s Guide. 

Programming Cable Pin 
Definitions 

Updated Table 3, Recommended Pin Connections. Added ECP5, iCE40LM, iCE40 Ultra, and 
MachXO3 device families. 

Target Board Design 
Considerations 

Updated section. Updated FAQ link on ispVM tool control of TCK duty cycle and/or 
frequency. 

Technical Support Assistance 

Updated Technical Support Assistance information. 

 

Revision 24.5, October 2012 

Section 

Change Summary 

Programming Flywire and 
Connection Reference 

Added iCE40 configuration port pin names to the Flywire Conversion Reference table. 

Programming Flywire and 
Connection Reference 

Added iCE40 information to Recommended Cable Connections table. 

 

Revision 24.4, February 2012 

Section 

Change Summary 

All 

Updated document with new corporate logo. 

 

Summary of Contents for HW-USBN-2B






















Reviews: