background image

Page 10 

 

Specifications 

 
Dimensions 

6 3/4" H X 15 1/2" W X 3 1/8" D 

 

17.1 cm H X 39 cm W X 7.9 cm D 

 

Weight 

9 lbs. (4.086 kg) 

 
Display 

3 3/4-Inch Red 4 Segment LED 

 

Housing 

  Extruded aluminum main case with black textured 

paint, molded plastic end caps with black texture. 

 
Line Power 

  115VAC, 80mA typical 

 

  220VAC, 80mA typical (optional) 

 

 

FCC 

Conforms to FCC Part 15 

 
 
Environment 

32

to 150

 o 

F (0

 o 

to 65

 o 

C) 

 

95% Relative Humidity (non-condensing) 

 
Mounting 

  Wall (surface)  

 

  Single Gang Box (surface) 

 

Double Face (wall or ceiling) (optional) 

 

Trademark / Copyright 

 
AirTime, Lathem and the Lathem logo are registered trademarks of Lathem Time 
Corporation. Other product names mentioned in this manual may be trademarks of their 
respective companies and are hereby acknowledged. 

WARNING: Changes or modifications to this product not expressly approved by the party 
responsible for compliance could void the user’s authority to operate this equipment. 

Copyright © 2009 Lathem Time Corporation. All rights reserved. 

 

All manuals and user guides at all-guides.com

Summary of Contents for Airtime AT-DDC4














Reviews: