background image

 

Page 11 

 

One Year Limited Warranty 

 

Lathem warrants the hardware products described in this guide against 
defects in material and workmanship for a period of one year from date 
of original purchase from Lathem or from an authorized Lathem reseller. 
The conditions of this warranty and the extent of the responsibility of 
Lathem Time Corporation (“Lathem”) under this warranty are listed 
below. 
1.

 

This  warranty  will  become  void  when  service  performed  by  anyone  other  than  an 
approved Lathem warranty service dealer results in damage to the product. 

2.

 

This  warranty  does  not  apply  to  any  product  which  has  been  subject  to  abuse, 
neglect,  or  accident,  or  which  has  had  the  serial  number  altered  or  removed,  or 
which has been connected, installed, adjusted, or repaired other than in accordance 
with instructions furnished by Lathem. 

3.

 

This  warranty  does  not  cover  dealer  labor  cost  for  removing  and  reinstalling  the 
machine for repair, or any expendable parts that are readily replaced due to normal 
use. 

4.

 

The  sole  responsibility  of  Lathem  under  this  warranty  shall  be  limited  to  repair  of 
this product, or replacement thereof, at the sole discretion of Lathem. 

5.

 

If it becomes necessary to send the product or any defective part to Lathem or any 
authorized  service  dealer,  the  product  must  be  shipped  in  its  original  carton  or 
equivalent, fully insured with shipping charges prepaid. Lathem will not assume any 
responsibility for any loss or damage incurred in shipping. 

6.

 

WARRANTY  DISCLAIMER  AND  LIMITATION  OF  LIABILITY:  Except  only  the  limited 
express  warranty  set  forth  above,  the  products  are  sold  with  no  expressed  or 
implied  warranties  of  any  kind,  and  the  implied  warranties  of  merchantability  and 
fitness for a particular purpose are hereby expressly disclaimed.   No warranties are 
given with respect to products purchased other than from Lathem or an authorized 
Lathem reseller and any such products are purchased "as is, with all faults."  In no 
event  will  Lathem  be  liable  for  any  direct,  indirect,  special,  incidental  or 
consequential  damages  arising  out  of  or  in  connection  with  the  delivery,  use  or 
inability  to  use,  or  performance  of  this  product.    In  the  event  any  limited  remedy 
given  herein  shall  be  deemed  to  have  failed  of  its  essential  purpose,  Lathem's 
maximum liability shall be to refund the purchase price upon return of the product. 

7.

 

Proof of date of purchase from Lathem or an authorized Lathem reseller is required 
for warranty service on this product. 

8.

 

This Warranty grants specific legal rights. Additional legal rights, which may vary by 
locale, may also apply. 

9.

 

Should any difficulties arise with the performance of this product during warranty, 
or  with  any  Lathem  authorized  service  centers,  contact  Lathem  Time

  at  the 

address below: 

 

Lathem Time 
200 Selig Drive, SW

 

Atlanta, GA  30336 

www.lathem.com

 

 

Document Number: USG0084 

 

All manuals and user guides at all-guides.com

Summary of Contents for Airtime AT-DDC4














Reviews: