Lasko S18601, User Manual

Page: 3 / 6

MODELO S18601
FUNCIONAMIENTO
Este Ventilador puede hacerse funcionar mediante los
Controles Manuales ubicados en la parte superior de
la unidad (como se muestra en la
Figura 10 ) o con el
Control Remoto (se muestra en la Figura 13 .
1. Conecte el cable eléctrico a un tomacorriente de 120 V~.
2. Conecte la energía eléctrica a su ventilador pulsando el
Botón Alimentación ( ).
3. VELOCIDAD DEL VENTILADOR: Ahora puede ajustar
la velocidad del ventilador presionando el botón de
velocidad del ventilador ( ).
4.
OSCILACION: Empuje la perilla ubicada en la parte su-
perior de la caja del motor para hacer que la cabeza del
Ventilador se mueva de un lugar hacia otro. (Figuras
11 y 12)
5. Después de apagar el Ventilador, desconecte la unidad
del tomacorriente eléctrico.
Rev. A 10/12 10
2084822
Rev. A 10/12
3 2084822
1. Take pipe assembly out of carton as shown.
(Figure 1)
2. Loosen Height Adjustment Nut turning counter clockwise .
(Figure 2)
3. Raise Extension Pipe . (Figure 3)
4. Tighten Height Adjustment Nu t turning clockwise .
(Figure 4)
STEP 1: PIPE ASSEMBLY
STEP 2: STAND ASSEMBLY
PLACE BASE FLAT ON FLOOR
1. With a twisting motion, insert the end of the large diameter
pipe into hole in Base. (Figure 5) Turning pipe while pushing
will assure pipe is fully seated in Base .
2. For Height Adjustment:
a) Loosen Height Adjustment Nut.
b) Raise or lower Extension Pipe to desired height.
c) Tighten Height Adjustment Nut .
1. Place Head Assembly with
Collar onto Extension Pipe.
(Figure 6)
2. Holding Extension Pipe
firmly, twist
Head Assembly
downward until seated on
Extension Pipe.
1. Tilt Head Assembly back. Put Rear Grill on Head Assembly.
(Figure 7)
2. Align tab of Plastic
Rear Grill
with groove on top of front
Head Assembly.
STEP 4: BLADE & GRILL ASSEMBLY
3. Fully seat Rear Grill and secure with Plastic Nut turning Clock-
wise. Slide Blade onto Motor Shaft. (Figure 8) Align Groove on
blade hub with Pin on motor shaft. (Figure 8A)
4. To secure Blade, screw Fan Spinner onto Shaft
Counter Clockwise until tight on Blade hub.
STEP 3: HEAD ASSEMBLY
Head
Assembly
Collar
Extension
Pipe
Figure 6
Botón
Alimentación
Figura 10
Figure 2 Figure 4 Figure 3 Figure 1
Height
Adjustment
Nut
Extension
Pipe
Rear
Grill
Figure 7
Rear Grill
Figure 8
Blade
Fan
Spinner
Plastic
Nut
Figure 8A
Pin
Groove
Hacia Arriba: Estacionario
Hacia Adelante: Oscilar
Figura 11 Figura 12
Botón
Velocidad del
Ventilador
Figure 5
Extension Pipe
Height
Adjustment Nut
Base
Front
Grill
5. With fan head in upright position, align Ornament of Front Grill
so it is horizontal and right side up. By starting with the top of
the grill and working down, snap Grill in place. NO GRILL CLIPS
ARE NEEDED FOR ASSEMBLY.
Do Not take pipe apart. Should pipes become separated, insert
pipe A into pipe B.
A
B
Head
Assembly
Larger
Pipe