MODELO R12210
NEW 12/14
2
R12210ES
NEW 12/14
7
R12210ES
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INFORMATION
When using electrical appliances, basic precautions should always be followed to reduce
the risk of fire, electrical shock and injury to persons, including the following:
Read all instructions before using this Fan.
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ALWAYS
FOLLOW THESE IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS:
•
AVOID
the use of extension cords, power strips, power taps, outlet style air fresheners or other cord connected device, as these
devices may overheat and cause a fire hazard.
•
DO NOT
route power cord under rugs, carpets, runners or furniture. This may damage the cord or cause it to overheat creating a fire
hazard.
•
ALWAYS
place the Fan on a stable, flat, level surface while in operation to prevent the Fan from overturning.
•
NEVER
insert or allow fingers or objects to enter grill openings while Fan is in operation or injury and/or damage to the Fan may occur.
•
DO NOT
block, cover or obstruct air flow to or from the fan while in operation.
•
DO NOT
use this Fan outdoors or near water or wet locations such as a bath tub, pool or hot tub. Use of this Fan in a wet location
may create a shock hazard.
•
DO NOT
run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture
or appliances. Arrange cord away from traffic area and where it will not be tripped over.
•
NEVER
use a single extension cord to operate more than one Fan or other electrical device.
•
DO NOT
use this Fan if it has been damaged or is not functioning properly.
•
THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008)
.This Fan is not suitable for use in agricultural
facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article
547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for agricultural buildings.
•
THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008)
.This Fan is not suitable for use in hazardous
locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical
requirements for hazardous locations.
CAUTION
DO NOT
use this fan to ventilate areas where flammable liquids or vapors are used, stored or are present, including paints,
gasoline, varnishes, floor refinishing products or solvents. ALWAYS read and follow all warnings and instructions on the
containers for these products!
ALWAYS
be sure the plug fits tightly into the outlet. When plugs fit loosely into outlets, they may slip partially out of the
outlet and create a poor connection. This may cause outlets to overheat and create a potential fire hazard. Outlets in this
condition should be replaced by a qualified electrician.
ALWAYS
unplug the power cord when servicing, cleaning or moving the Fan. DO NOT use the ON/OFF switch as the sole
means of disconnecting power. NEVER leave children unattended when the Fan is on or plugged in. ALWAYS turn off and
unplug the Fan when not in use.
BE CERTAIN
that the power source for the Fan is 120V AC. DO NOT plug the Fan into 240V or other power source.
The power cord is equipped with a three-prong grounded plug that must be inserted into a matching receptacle. Under no
circumstances should the grounding prong be cut off the plug. Where a two-prong wall receptacle is encountered, it must be
replaced with a properly grounded three-prong receptacle installed in accordance with the National Electrical Code (NEC) and
all applicable local codes and ordinances. This work must be done only by a qualified electrician, using copper wire only.
The
Blue Plug™
on your Lasko fan is a safety feature. It contains a non-replaceable safety device (fuse) that should not be
removed or tampered with. To reduce the risk of fire, electric shock and personal injury,
DO NOT
attempt to remove, replace,
repair or tamper with the originally supplied plug. If the Fan has stopped functioning, it may be due to the safety device
incorporated in this plug.
DO NOT USE A THREE-PRONG TO TWO-PRONG ADAPTER. IMPROPER CONNECTION MAY CREATE THE RISK OF ELEC-
TRICAL SHOCK. USE OF SUCH ADAPTERS IS NOT PERMITTED IN CANADA.
OPERACION
1. Empuje la perilla de oscilación hacia abajo en el estuche del
motor para hacer que la cabeza del ventilador se mueva de lado
a lado. (Figura 1)
2. VELOCIDAD: Control de la velocidad del ventilador utilizando
la perilla de velocidad de la parte trasera del motor.
3 - Velocidad alta
2 - Velocidad media
1 - Velocidad baja
INCLINACION: Este ventilador está equipado con una cabeza de
ventilador multi-ángulo para circulación de aire por toda la habitación.
Para poder cambiar el ángulo de funcionamiento del ventilador, ponga
una mano sobre el ventilador. Use su otra mano para aflojar la perilla
de ajuste y coloque el ventilador en la posición deseada. Una vez que
el ventilador esté en la posición deseada vuelva a apretar la perilla
de ajuste. (Figura 2)
Soportes
de la rejilla
Ranura
del tornillo
Agujero
del tornillo
roscado
Ranuras de los so-
portes de la rejilla
Figura 7
Figura 8
Figura 5
Tornillo
preinstalado
del aspa del
ventilador
Figura 4
Ganchos
Figura 3
Perilla de ajuste
Figura 2
Perilla de
oscilación
Interruptor de
velocidades
Figura 1
Instalar únicamente
en esta dirección
Tornillo de
fijación
Aros
Figura 6
DESARMAR PARA LIMPIAR
1. Siempre desconecte el cable antes de moverlo, realizarle el
mantenimiento o limpiarlo.
2. Afloje el tornillo de fijación del anillo de la rejilla y separe el anillo de
la rejilla de los aros delanteros y traseros de las rejillas. (Figura 3)
3. Desconecte la rejilla delantera y trasera al desengancharlas. Los
ganchos de la rejilla trasera se soltarán de la rejilla delantera. (Figura 4)
4. Use un destornillador Phillips #2 (de estrella), afloje el tornillo
de la parte trasera del aspa del ventilador, y deslice el aspa del
ventilador fuera del eje del motor. (Figuras 5 y 6)
5. Afloje y saque el tornillo y la arandela de seguridad del soporte de
montaje inferior de la rejilla trasera. Deslice la rejilla hacia arriba y
separe la rejilla trasera y la caja del motor para desconectar los dos
soportes superiores de la rejilla de las ranuras de la caja del motor.
(Figuras 6, 7 y 8) Cuando vuelva a instalar el aspa del ventilador, deje
el tornillo empotrado en el eje del motor. Asegúrese de que el aspa
del motor esté reinstalada con el lado del tornillo primero. (Figura 5)
6. Vuelva a instalar los componentes de la misma manera en que fueron
retirados.
