Figure 2
Figure 4
Figure 3
Figure 1
Height
Adjustment
Nut
Extension
Pipe
MODELO S18924
FUNCIONAMIENTO
Este Ventilador puede hacerse funcionar mediante los
Controles Manuales ubicados en la parte superior de
la unidad (como se muestra en la
Figura 10
) o con el
Control Remoto (se muestra en la
Figura 13
).
1. Conecte el cable eléctrico a un tomacorriente de 120
V~.
Asegúrese que el enchufe encaje firmemente
en el tomacorriente.
Cuando los enchufes quedan flojos en los
tomacorrientes, pueden deslizarse parcial
o completamente fuera del tomacorriente
con un leve movimiento del cable adosado.
Los tomacorrientes en este estado podrían
sobrecalentarse y representar un grave peligro de
incendio; si está cubierto por una cortina o tela,
el riesgo de incendio es aún mayor.
2. Conecte la energía eléctrica a su ventilador pulsando el
Botón Alimentación
( ).
3.
VELOCIDAD DEL VENTILADOR:
Ahora puede ajustar
la velocidad del ventilador al nivel deseado - 1 (baja), 2
(mediana) ó 3 (alta) - pulsando el
Botón Velocidad
( ).
4.
FUNCIÓN DE TEMPORIZADOR:
Este ventilador está
equipado con un temporizador que le permite a usted
establecer la duración de la operación oprimiendo el
Botón de Función Temporizador
( ) manualmente en
el área de control del ventilador, o presionando el
Botón
Temporizador
( ) en el control remoto. El temporizador
puede ser programado 1, 2 o 4 horas. Continúe oprim-
iendo el
Botón Temporizador
( ) para lograr el tiempo de
programación deseado. Para cancelar el temporizador,
presione el botón del temporizador hasta que se apague
la luz.
5.
OSCILACION:
Empuje la perilla ubicada en la parte su-
perior de la caja del motor para hacer que la cabeza del
Ventilador se mueva de un lugar hacia otro.
(Figuras 11 y 12)
6.
Después de apagar el Ventilador, desconecte la unidad
del tomacorriente eléctrico.
REV A 5/15
10
2084850
REV A 5/15
3
2084850
1. Take pipe assembly out of carton as shown.
(Figure 1)
2. Loosen
Height Adjustment Nut
turning counter clockwise.
(Figure 2)
3. Raise
Extension Pipe
.
(Figure 3)
4. Tighten
Height Adjustment Nut
turning clockwise.
(Figure 4)
STEP 1: PIPE ASSEMBLY
STEP 2: STAND ASSEMBLY
1. Place
Head Assembly
with
Collar
onto
Extension Pipe
.
(Figure 6)
2. Holding
Extension Pipe
firmly,
twist
Head Assembly
downward
until seated on
Extension Pipe
.
1. Tilt
Head Assembly
back. Put
Rear Grill
on Motor.
(Figure 7)
2. Align tab of Plastic
Rear Grill
with groove on top of front
Motor
cover.
STEP 4: BLADE & GRILL ASSEMBLY
3. Fully seat
Rear Grill
and secure with
Plastic Nut
turning Clock-
wise. Slide
Blade
onto
Motor Shaft.
(Figure 8)
Align
Groove
on
blade hub with
Pin
on motor shaft.
(Figure 8A)
4. To secure
Blade
, screw
Spinner
onto Shaft Counter
Clockwise until tight on Blade hub.
STEP 3: HEAD ASSEMBLY
Head
Assembly
Collar
Extension
Pipe
Figure 6
5. With fan head in upright position, align
Ornament
of
Front Grill
so it is horizontal and right side up. Starting with the top of the
grill and working down, insert
Snaps
on
Rear Grill
through
Slots
in
Front Grill
.
(Figure 9)
Botón
Alimentación
Botón Función de
Temporizador
Figura 10
Rear
Grill
Figure 7
Motor
Rear Grill
Figure 8
Blade
Fan
Spinner
Plastic
Nut
Ornament
Slots
Snaps
Rear Grill
Front Grill
Figure 9
Hacia Arriba: Estacionario
Hacia Adelante: Oscilar
Figura 11
Figura 12
Botón
Velocidad del
Ventilador
PLACE BASE FLAT ON FLOOR
1. With a twisting motion, insert the end of the large diameter
pipe into hole in
Base
.
(Figure 5)
Turning pipe while pushing
will assure pipe is fully seated in
Base
.
2. For Height Adjustment:
a) Loosen
Height Adjustment Nut
.
b) Raise or lower
Extension Pipe
to desired height.
c) Tighten
Height Adjustment Nut
.
CAUTION:
When making height adjustment
after head assembly is attached,
ALWAYS support extension pipe
with one hand, as loosening
height adjustment nut may
otherwise cause rapid fall of
extension pipe and head
assembly.
Quick Assembly Video: Scan
with Smart Phone or visit www.
laskoproducts.com/how-to
Figure 5
Extension
Pipe
Height
Adjustment
Nut
Base
Figure 8A
Pin
Groove