Figura 4
Proteja
Tuerca
Rejilla Trasera
1. Coloque el ventilador sobre una superficie firme y nivelada.
ADVERTENCIA:
Los tacos de plástico o hule, tales como las
patas de esta unidad, pueden pegarse a la superficie de los muebles.
La unidad podría dejar un residuo capaz de oscurecer, manchar o
dejar marcas permanentes en el acabado de ciertas superficies de
muebles, incluyendo superficies y pisos de madera.
2. Conecte el cable eléctrico a un tomacorriente de 120 voltios.
Asegúrese que el enchufe encaje firmemente en el
tomacorriente.
Cuando los enchufes quedan flojos en los
tomacorrientes, pueden deslizarse parcial o
completamente fuera del tomacorriente con un leve
movimiento del cable adosado. Los tomacorrientes
en este estado podrían sobrecalentarse y representar
un grave peligro de incendio; si está cubierto por una
cortina o tela, el riesgo de incendio es aún mayor.
Rev. C 2/11
2
2085470
Rev. C 2/11
7
2085470
1. Inserte el soporte en la base al presionar por encima de los
sujetadores para conectarlos.
(Figura 1)
4. Apriete con la tuerca de protección en el sentido de las agujas
del reloj.
(Figura 4)
5. Deslice la
Hélice
en el eje del motor.
(Figura 5)
(Alinear la
Ranura
Del Cubo
de la tapa con el
Pasador
del eje del motor.
Figura 5A
)
6. Para asegurar la
Helice
, enroscarla hasta que quede
apretada en el
Cubo de la Tapa
haciéndola girar
Hacia la Izuierda.
Base
Figura 1
Figura 5
2. Inserte el ensamblaje superior en el soporte. Alinee la muesca
del cable con la del soporte. No pase el cable por el soporte.
(Figura 2)
3. Inclinar la cabeza del ventilador hacia atrás. Coloque la
Re-
jilla Trasera
en el
Motor
. (La marca UP indica la parte superior.)
(Figura 3)
Figura 6
Parrilla
Delantera
Figura 2
ARMADO
Endidura
Motor
Rejilla Trasera
Hélice
FUNCIONAMIENTO
MODEL 5132
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce
the risk of fire, electrical shock and injury to persons, including the following:
SAVE THESE INSTRUCTIONS
Read all instructions before using this Fan.
1. Make certain the power source conforms to the electrical requirements of the Fan.
2. Make certain that the room is equipped with a working smoke detector.
3. Use this Fan only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock,
or injury to persons.
4. To reduce the risk of personal injury and electric shock, the Fan should not be played with or placed where small children can reach it.
5. Unplug power cord before installing, servicing, or moving the Fan.
DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN SERVICING
OR MOVING THE FAN. ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND UNPLUG FAN BEFORE
LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE FAN IS ON OR PLUGGED IN.
6. This Fan must
NOT
be used in potentially dangerous locations such as flammable, explosive, chemical-laden or wet atmospheres
where gasoline, paint or flammable liquids are used or stored.
7.
DO NOT
use Fan in or near a window. Rain may create an electrical hazard.
8. Completely assemble Fan, according to instructions, before connecting to power supply.
REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK - DO NOT USE THIS FAN
WITH ANY SOLID STATE SPEED CONTROL DEVICES.
9. Where possible, avoid the use of extension cords because the extension cord may overheat and cause a fire. If you must use an exten-
sion cord, minimize the risk of overheating by using the shortest cord possible and ensuring that it is UL listed.
NEVER
use a single
extension cord to operate more than one Fan. Do not plug Fan into any other cord connected device, such as a power strip, cord
reel, surge protector, multiple outlet adapters or outlet-type air fresheners. The use of such devices may create a fire hazard.
10.
NEVER
operate any Fan with a damaged cord or plug or after the Fan malfunctions, has been dropped or damaged in any
manner.
11.
NEVER
insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock or fire,
or damage the Fan. To reduce the risk of fire,
DO NOT
block or tamper with the Fan in any manner while it is in operation.
12. Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the
Power Cord so the Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord
with throw rugs, runners, or similar coverings. Arrange Power Cord away from room traffic and where it will not be tripped over.
13. This Fan is not intended for use in wet or damp locations.
NEVER
locate a Fan where it may fall into a bathtub or other water con-
tainer.
NEVER
use Fan where flammable liquids are used or stored.
14.
NEVER
use Fan outdoors.
15. This Fan is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please
refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical require-
ments for Agricultural Buildings.
THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
16. This Fan is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or
local codes or standards relating to electrical requirements for Hazardous locations.
THIS FAN DOES NOT MEET THE REQUIRE-
MENTS OF NEC ARTICLE 500 (2008).
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock,
this plug is intended to fit in a polarized outlet only one way. Match wide blade of plug to wide slot. Fully
insert. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. DO NOT attempt to defeat this safety feature.
This plug is a safety feature. It contains a safety device (fuse) that should not be removed. Discard product
if the attachment plug is damaged. To reduce the risk of fire, electric shock and personal injury, DO NOT
remove, replace, repair or tamper with the originally supplied plug. If the Fan does not function properly, it
may be due to the safety device incorporated in this plug. Call 800-233-0268, Monday - Friday, between 8:00
a.m. and 5:00 p.m. Eastern. If the plug warning label is missing or damaged, call the toll free number for a
replacement label.
Cabeza de
Ensamblaje
Sujetadores
de
Ensamblaje
Soporte
7. Con la Cabeza del Ventilador inclinada hacia atrás y centrada,
alinear el Adorno de tal manera que la divisa quede horizontal.
Insertar la parte inferior de la Rejilla Delantera dentro de la Rejilla
Trasera. La proyección de la parte inferior de la Rejilla Trasera
debe quedar entre dos Alambres de la parte delantera. Cerrar
apretando la parte delantera contra la parte trasera empezando
en la parte superior y continuar cerrando hacia abajo ambos
lados. NO NECESITO EL GANCHOS DE LA REJILLA PARA
ENSAMBLE.
(Figura 6)
El cable
Figura 3
Rejilla Trasera
Ranura Del Cubo
Pasador
Figura 5A
