Lasermet ULTRA LEDS-ULT-470 Instruction Manual Download Page 3

Page: 3 / 13

LED Ultra Sign Instruction Manual

00625-53-000

Page 3 of 13

Issue 4.1 19 January 2021

Declaration of Conformity

LASERMET LIMITED

LEDS-ULT-470

00625-00-000 Standard

00864-00-000 High Reliability

00865-00-000 Dimmable

00866-03-000 High Reliability Dimmable

DECLARATION OF CONFORMITY

This is to certify that the LED Ultra Signs designated by Lasermet Part Number LEDS-
ULT-470

has been tested in accordance with the following directives and standards and

found to comply.

Lasermet certifies that this product complies with the basic requirements for health
and safety as provided by the following directives and standards:

Directives:

Low Voltage Directive 2014/35/EU

EMC Directive 2014/30/EU
CE Directive 93/68/EEC

Standards:

EN 60598-1:2008

EN 62471:2008

EN 55015:2006

EN 61547:1995 inc. A1:2000

EN 61547:2009

Supplier:

Lasermet Limited
Lasermet House
137 Hankinson Road
Bournemouth
BH9 1HR
Dorset
United Kingdom

Country of Origin: England

Date: 9 December 2019

Summary of Contents for ULTRA LEDS-ULT-470














Search results

Summary of Contents for ULTRA LEDS-ULT-470

Reviews:

Related manuals for ULTRA LEDS-ULT-470

Brands by name

Popular brands

Lasermet ULTRA LEDS-ULT-470, Instruction Manual

Search results

Summary of Contents for ULTRA LEDS-ULT-470

Reviews:

Related manuals for ULTRA LEDS-ULT-470

Brands by name

Popular brands