background image

ICS-7-OEM Instruction Manual 

 

02058-53-000 

Page 5 of 29

 

Issue 3          19 January 2021 

 

Concept 

 
The ICS-7-OEM provides control of an interlock system primarily intended to protect persons from 
accidental exposure to hazardous lasers. It is able to monitor several doors, windows, curtains etc. 
fitted with safety  interlock  switches and  disable the  laser if  any  are  open. In this  manual the  term 
‘Door Switch’ refers to any interlock switch which may be fitted to a door, cover, window blind etc. 
 
The versatile ICS-7-OEM system can be connected to any number of door switches and can indicate 
the status of up to 6 switches or groups of switches. 
 
Two  external  volt-free  contacts  are  required  to  arm  the  system.  These  might  be  from  a  PLC,  for 
example.  When  these  contacts  are  both  closed,  provided  the  necessary  interlock  input  conditions 
are met (e.g. doors closed), the Controller will arm and enable the laser. If the Arm contacts are then 
opened the system will disarm. 
 
If any interlock  input (e.g. door)  is open when the external Arm  contacts  are  closed the  controller 
will  not  arm.  If  the  interlock  is  then  closed  the  controller  will  still  not  arm.  This  is  to  prevent  an 
unexpected start-up of the laser. If the system fails to arm because an interlock is open (e.g. door 
open), the Arm request should be removed and the interlock closed (e.g. close the door). 
 
The  ICS-7-OEM  has  a  fully  dual  channel  cross-checked  architecture  and  when  correctly  wired  can 
realise a system compliant with EN ISO 13849-1 up to performance level ‘e’. 
 
Eight  safety  interlock  outputs  each  rated  at  4A  resistive,  50VDC,  are  provided to  enable  the  laser, 
operate door locks, or provide signals to a PLC. The interlock outputs are volt-free contacts. Seven 
outputs  close  when  the  system  is  armed.  The  other  output  is  normally  closed  and  opens  when 
armed.  Each  output  actually  comprises  two  contacts,  one  for  each  channel,  operated  by  different 
relays. In the event of one contact failing to open, the other contact will open and the system is 
then disabled, preventing further use and maintaining safety. The contacts can be configured for a 
variety of options. 
 
The ICS-7-OEM is able to directly control and monitor safety-rated power contactors which may be 
used to switch single or three-phase laser mains supplies. 
 
The ICS-7-OEM is able to monitor output devices such as shutters with feedback (such as Lasermet’s 
LS-20 and LS-200 beam shutters). 
 
The controller has a pair of isolated volt-free contacts which close in the disarmed state provided all 
monitored devices are  proven to be  in the  safe  condition. These  contacts may be used  to operate 
the ‘system disarmed’ or ‘laser off’ section of a dual message illuminated sign. They are marked as 
‘System Disarmed’ on the unit.  
 
The  controller  also  has  a  pair  of  contacts  which  close  to  indicate  that  all  the  interlock  inputs  are 
closed. This may be used, for example, to signal to a PLC that all doors are closed and is marked as 
‘Doors Closed’ on the unit label. 
 
The ICS-7-OEM has a mismatch detector which when wired to a full dual-channel system disables the 
system in the event of a mismatch between the two safety circuits. This provides protection against 
the single failure of a door switch etc. 

Summary of Contents for ICS-7-OEM






























Reviews: