LaserLiner Quadrum OneTouch Manual Download

Page: 12 / 13

Quadrum OneTounch / Quadrum OneTounch Green

Adjustment mode

Take the alignment of the rotary laser into account when
performing adjustment work. Always adjust all the axes.

X axis adjustment

Activate adjustment mode: Switch on the Quadrum OneTouch.
Press the Y axis plus/minus buttons simultaneously until the X LED
flashes rapidly.

Adjustment: Use the X axis plus/minus buttons to move the laser
from its current position to the height of reference point A2.

Cancel adjustment: Switch the device off.

Save: Press the Y axis plus/minus buttons simultaneously until
the X LED comes on.

Y axis adjustment

Activate adjustment mode: Switch on the Quadrum OneTouch.
Press the X axis plus/minus buttons simultaneously until the Y LED
flashes rapidly.

Adjustment: Use the Y axis plus/minus buttons to move the laser
from its current position to the height of reference point A2.

Cancel adjustment: Switch the device off.

Cancel adjustment: Switch the device off. Save: Press the X axis
plus/minus buttons simultaneously until the Y LED comes on.

X- / Y-
Axis

Regularly check the adjustment
before use, after transport and after
extended periods of storage. Always
make sure to control all axes.

Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 23

10.03.11 08:59

Summary of Contents for Quadrum OneTouch













