background image

15

Quadrum OneTounch / Quadrum OneTounch Green

 

Transport LOCK: The device is protected by a special motor 

brake during transport.

IP 66

 

The device characterised by specific protection against 

dustand rain.

Quadrum OneTouch Green: green laser technology

The distance at which a laser is visible to the naked eye depends on its colour 
i.e. wavelength. This is because of the human eye's physiology – green 
appears brighter to us than red. Depending on ambient light, green lasers 
are therefore many times more visible than red lasers; in indoor areas this is 
as much as 12 times brighter. This permits applications on dark surfaces, over 
longer distances and work in very bright ambient light. A red laser with a 635 
nm wavelength is used as a reference value for brightness differentiation.
In contrast to red lasers, green laser light can only be produced indirectly. 
This is a source of potential characteristic fluctuations: 
–  The optimal operating temperature is 20°C. Outside its operating 

temperature range of 0 – 40°C Quadrum OneTouch Green is darker. 
IMPORTANT: Allow the unit enough time to adapt to the ambient 
temperature before switching the unit on. 

–  Laser brightness may vary somewhat from one unit to another. This is a 

natural phenomena and excluded from warranty claims. 

–  Green Laser will only work with certain Receivers. The maximum range 

of the Receiver is shorter, please refer to technical details.

Horizontal 
levelling

Slope function

auto

man

Space grids:

 These show the laser planes and functions.

auto: Automatic alignment / man: Manual alignment

GB

Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd   15

10.03.11   08:59

Summary of Contents for Quadrum OneTouch














Reviews: