background image

 

 
 
 
This product is guaranteed against defects in materials and workmanship for both parts and labor, under 
normal working conditions for two years from the date of purchase, except as noted herein. LaserLine 
Mfg., Inc. liability under this warranty is limited to repairing or replacing any product returned to an 
authorized service center for that purpose. Any evidence of attempts to repair this unit by other than 
factory authorized personnel automatically voids the warranty. LaserLine Mfg., Inc. does not take 
liability for any damages caused by non-accuracy of this product. Before using the product always check 
for accuracy per the enclosed instructions in this manual. 

 
 
 

Warning!  

 

Under no circumstances, attempt to open or disassemble the Laser Housing. Doing so may cause 
exposure to potentially hazardous levels of laser light. 
 
 
Caution: Use of controls or adjustments or performance of procedures other than those specified 
herein may result in hazardous laser light exposure. 
 

Factory Service Center 

LaserLine MFG., INC. 
1810 S.E. First Street, Suite H, 
Redmond, OR 97756 
(P) 541-548-0882 
(F) 541-548-0892 
(Email) [email protected] 
 
 

For all Warranty:

 Call Order Processing for RMA # at 541-548-0882. The Unit will be repaired and 

returned by prepaid freight. 
 

All Non-Warranty Repairs: 

Send to: LaserLine MFG., INC. at above address 
 

Out of Warranty Repairs:

 1 Year on replacement parts, 90 days on labor. 

 
 
 

 
 
 

 

 

 

 

WARRANTY 

Summary of Contents for 4003-0000-U












Reviews: