Laser Technology TruPulse L2 User Manual Download Page 25 | Manualshive

Page: 25 / 30

Laser Technology TruPulse L2 User Manual Download Page 25

Laser Technology, Inc. TruPulse L2 User’s Manual 1st Edition

Section 6 - System Setting Menu

Page 23

Copyright© 2023, Laser Technology, Inc. All rights reserved.

Units of Measurements (UoM)

The TruPulse L2 allows you to choose the units of measure. Distance: meters or feet. Inclination: Degrees or % Slope. To change
the units of measurement option:

1. Press-and-hold Display/Menu button
2. Then press Up or Down Arrow buttons to scroll until the UoM option screen is displayed.

•

The last UoM options chosen will be displayed.

3. Press Display/Menu button to enter option selections, the icon will be displayed indicating the UoM option menu.
4. Then press the Up or Down buttons to scroll though UoM options.
5. Press the Fire button to select the UoM option and ready to measure.

NOTE Each time the TruPulse L2 is powered ON, it will return to the same unit setting that was last used.

Units of Measurements Workflow

Figure 23

«
...
23
24
25
26
27
...
»

Summary of Contents for TruPulse L2































Reviews:

No comments