background image

 

1706K45B 

 

Page 23 of 27 

Communication with commands through RS-485 

The displays can obtain the displayed parameters through commands, as well as force the display time 
through RS-485 commands. In this case, the display must be configured for not to sync another way or the 
sync will rewrite the programmed time. The frames are sent in ASCII (character) format. The end of block is 
the one defined by user in parameter 9.3 

The following frames can be sent 

Command 

Code 

Display 

address 

Data 

End of block 

Display time request 

P H 

 

 

 

Time programming 

F H 

 

 

 

 

Display time request 

Frame 

This frame only includes the code. This does not send any data. 

 

Code 

Address 

End of block 

ACII 

P H 

H L 

 

Hexa 

50h 48h 

 

 

 

Example: Request time from the display in address 03. 

 

Code 

Address 

End of block 

ACII 

P H 

03 

 

Hexa 

50h 48h 

30h 33h 

 

Response frame 

 

Code 

Address 

Data 

End of block 

 

Code 

Address 

Day  Month  Year 

Space 

Hour 

Minute 

Second 

End of block 

ASCII 

R H 

H L 

DD 

MM 

AA 

 

HH 

MM 

SS 

 

Hexa 

52h 48h 

 

 

 

 

20h 

 

 

 

 

 

Example: Response from the frame sent in the example before. Time is 13:16:00  16/05/2013 

 

Code 

Address 

Data 

End of block 

 

Code 

Address 

Day 

Month 

Year 

Space 

Hour 

Minute 

Second 

End of block 

ASCII 

R H 

03 

16 

05 

13 

 

13 

16 

00 

 

Hexa 

52h 48h 

30h 33h 

31h 36h 

30h 35h 

31h 33h 

20h 

31h 33h 

31h 36h 

30h 30h 

 

 

 

 

Summary of Contents for DR-129



























Reviews: