FOR MINOR REPAIRS FOLLOW THIS PROCEDURE:
1. Clean the area to be repaired and clear it of wax and
oil.
2. Thoroughly clean out nicks, chips and scratches.
3. Sand area to be repaired so gelcoat will bond.
4. IN A SEPARATE CONTAINER, MEASURE ONLY THE
AMOUNT OF GELCOAT YOU NEED. Mix a 2% ratio
of catalyst to the amount of gelcoat being used (a
spoonful of gelcoat will require only a drop or two of
catalyst).
NOTE: DO NOT pour any unused portions of the
gelcoat/catalyst mixture back into either original container.
5. Apply gelcoat to area leaving a slight lift above the sur-
face.
6. Cover with wax paper (lack of oxygen helps mixture
set) and let set 20 to 30 minutes.
7. Remove wax paper and shave off excess gelcoat with
a razor blade.
8. By the time the area is shaved smooth, you are ready
to sand (Use 400 to 600 grade sandpaper, NO SUB-
STITUTES).
9. Rub or buff the fiberglass with automotive cleaner com-
pound, then wax.
Some discoloration may occur if your boat has weathered.
For your first attempt at repair, experiment on an area not
normally visible. With a little experience, even the novice
can repair a scratch with few, if any, visible repair marks.
Hardware and Fittings
Chrome, stainless steel, and aluminum hardware should
be cleaned with water and a cloth, followed with either an
application of commercial aluminum or chrome cleaner.
For excessively dirty or oily hardware, use alcohol. AVOID
THE USE OF DETERGENTS OR ABRASIVES WHEN
CLEANING HARDWARE.
Inspect all hardware and fittings to make sure they are
secure. All screws, bolts, clamps, cleats, etc., must be
tight.
UPHOLSTERY
Your boat’s seats and vinyl upholstery should be kept as
clean as the exterior finish to prolong life and beauty.
Seat Coverings & Vinyl
The seat coverings and vinyl trim are made of temperature
resistant vinyl.
1. Always try to clean up spills quickly to prevent staining.
2. Clean dirt and smudges with mild soap and warm
water. If necessary, scrub with a soft bristle brush to
remove dirt from textured vinyl. Dry with a soft, lint-free
cloth or towel.
3. MSG Final Finish Cleaner is recommended for clean-
ing your interior vinyl. It may be purchased from your
local dealer.
4. Certain household cleaners, powdered abrasives, steel
wool and industrial cleaners can cause damage and
discoloration and are not recommended. Dry cleaning
fluids and lacquer solvents should not be used as they
will remove the printed pattern and gloss. Waxes
5.3
FOR MINOR REPAIRS FOLLOW THIS PROCEDURE:
1.
Clean the area to be repaired and clear it of wax and
oil.
2.
Thoroughly clean out nicks, chips and scratches.
3.
Sand area to be repaired so gelcoat will bond.
4.
IN A SEPARA
TE CONTAINER, MEASURE ONL
Y THE
AMOUNT OF GELCOAT YOU NEED. Mix a 2% ratio
of catalyst to the amount of gelcoat being used (a
spoonful of gelcoat will require only a drop or two of
catalyst).
NOTE:
DO NOT pour any unused portions of the
gelcoat/catalyst mixture back into either original container.
5.
Apply gelcoat to area leaving a slight lift above the sur-
face.
6.
Cover with wax paper (lack of oxygen helps mixture
set) and let set 20 to 30 minutes.
7.
Remove wax paper and shave off excess gelcoat with
a razor blade.
8.
By the time the area is shaved smooth, you are ready
to sand (Use 400 to 600 grade sandpaper, NO SUB-
STITUTES).
9.
Rub or buff the fiberglass with automotive cleaner com-
pound, then wax.
Some discoloration may occur if your boat has weathered.
For your first attempt at repair, experiment on an area not
normally visible. With a little experience, even the novice
can repair a scratch with few, if any
, visible repair marks.
Hardware and Fittings
Chrome, stainless steel, and aluminum hardware should
be cleaned with water and a cloth, followed with either an
application of commercial aluminum or chrome cleaner.
For excessively dirty or oily hardware, use alcohol. AVOID
THE USE OF DETERGENTS OR ABRASIVES WHEN
CLEANING HARDWARE.
Inspect all hardware and fittings to make sure they are
secure. All screws, bolts, clamps, cleats, etc., must be
tight.
UPHOLSTERY
Your boat’
s seats and vinyl upholstery should be kept as
clean as the exterior finish to prolong life and beauty.
Seat Coverings & Vinyl
The seat coverings and vinyl trim are made of temperature
resistant vinyl.
1.
Always try to clean up spills quickly to prevent staining.
2.
Clean dirt and smudges with mild soap and warm
water. If necessary
, scrub with a soft bristle brush to
remove dirt from textured vinyl. Dry with a soft, lint-free
cloth or towel.
3.
MSG Final Finish Cleaner is recommended for clean-
ing your interior vinyl. It may be purchased from your
local dealer.
4.
Certain household cleaners, powdered abrasives, steel
wool and industrial cleaners can cause damage and
discoloration and are not recommended. Dry cleaning
fluids and lacquer solvents should not be used as they
will remove the printed pattern and gloss. Waxes
5.3
