background image

not turn as many persons under the same conditions as a
Type I.

PFD TYPE III, WEARABLE

Type III allows the wearers to place themselves in a verti-
cal or slightly backward position. Type III has the same
buoyancy as a Type II PFD. It has little or no turning ability.

PFD TYPE IV, THROWABLE (REQUIRED IN ADDITION TO
THE ABOVE MENTIONED PFDs YOU MUST HAVE ONE
TYPE IV THROWABLE PFD ON BOARD)

The PFD Type IV can be thrown to a person in the water,
grasped and held by the user until rescued. The design
does not allow for it to be worn. The most common Type IV
PFDs are a buoyant cushion or ring buoy. The throwable
Type IV PFD shall be immediately available for use and in
serviceable condition.

PFD TYPE V WEARABLE

This PFD must be worn to be effective. When inflated, it pro-
vides buoyancy equivalent to Type I, II or III PFDs. When it is
deflated, however, it may not support some people.

Fire Extinguishers

All Class 1 (16 to 26 feet) powerboats are required to carry
one (1) B-I type hand portable fire extinguisher, if not
equipped with a fixed (Halon) fire extinguishing system in
the engine compartment.

All Class 2 (up to 39.4 feet) powerboats are required to carry
two (2) B-I type hand portable fire extinguisher, if not
equipped with a fixed (Halon) fire extinguishing system in
the engine compartment. When equipped with a fixed
(Halon) fire extinguishing system, only one (1) B-I type hand
portable fire extinguisher is required.

All hand portable fire extinguishers should be mounted in a
readily accessible location, and away from the engine com-
partment. All persons aboard should know the location and
proper operation of the fire extinguisher(s).

If your fire extinguisher has a charge indicator gauge, cold
or hot weather may have an effect on the gauge reading.
Consult the instruction manual supplied with the fire extin-
guisher to determine the accuracy of the gauge. 

Visual Distress Signal Devices

Visual Distress Signal devices are required and may be of
the pyrotechnic or non-pyrotechnic type. The regulation
requires all recreational boats when used on coastal
waters, which includes the Great Lakes, territorial seas
and those waters directly connected to the Great Lakes
and the territorial seas, up to a point where the waters are
less than two miles wide, and the boats owned in the
United States when operating on the high seas, to be
equipped with visual distress signal devices.

Pyrotechnic and non-pyrotechnic equipment must be U.S.
Coast Guard approved, in serviceable condition and
stowed in a readily accessible location. Equipment provid-
ing a date for serviceable life, must be within the specified
usage date as shown.

PYROTECHNIC EQUIPMENT

Pyrotechnic U.S. Coast Guard approved visual distress
signals and associated equipment include:

Red flares, hand held or aerial

Orange smoke, hand held or floating

Launchers for aerial red meteors or parachute flares

1.19

not turn as man

y persons under the same conditions as a

T ype I.

PFD TYPE III, WEARABLE

T ype III allo

ws the wearers to place themselv

es in a ver

ti-

cal or slightly backw

ard position. T ype III has the same

buo

yancy as a T

ype II PFD. It has little or no tur

ning ability .

PFD TYPE IV , THROW

ABLE (REQUIRED IN ADDITION TO

THE ABOVE MENTIONED PFDs YOU MUST HAVE ONE

TYPE IV THROWABLE PFD ON BOARD)

The PFD T ype IV can be thro

wn to a person in the water

,

grasped and held b

y the user until rescued. The design

does not allow f

or it to be wor

n. The most common T ype IV

PFDs are a buo

yant cushion or r

ing buo

y . The thro

wab

le

T ype IV PFD shall be immediately a

vailab

le for use and in

serviceab

le condition.

PFD TYPE V WEARABLE

This PFD must be w

orn to be eff

ective

. When inflated, it pro-

vides buo

yancy equiv

alent to T ype I, II or III PFDs

. When it is

deflated, how

ever

, it may not suppor

t some people.

Fire Extinguishers

All Class 1 (16 to 26 feet) po

werboats are required to carr

y

one (1) B-I type hand portab

le fire extinguisher

, if not

equipped with a fixed (Halon) fire e

xtinguishing system in

the engine compartment.

All Class 2 (up to 39.4 feet) po

werboats are required to carr

y

two (2) B-I type hand por

table fire e

xtinguisher, if not

equipped with a fixed (Halon) fire e

xtinguishing system in

the engine compartment. When equipped with a fix

ed

(Halon) fire extinguishing system, only one (1) B-I type hand

portab

le fire extinguisher is required.

All hand portab

le fire extinguishers should be mounted in a

readily accessible location, and a

wa

y from the engine com-

partment. All persons aboard should kno

w the location and

proper operation of the fire e

xtinguisher(s).

If your fire e

xtinguisher has a charge indicator gauge, cold

or hot weather ma

y have an eff

ect on the gauge reading.

Consult the instruction man

ual supplied with the fire extin-

guisher to determine the accur

acy of the gauge. 

Visual Distress Signal Devices

Visual Distress Signal devices are required and ma

y be of

the pyrotechnic or non-p

yrotechnic type. The regulation

requires all recreational boats when used on coastal

waters

, which includes the Great Lakes

, territor

ial seas

and those waters directly connected to the Great Lak

es

and the territor

ial seas, up to a point where the w

aters are

less than two miles wide

, and the boats owned in the

United States when operating on the high seas

, to be

equipped with visual distress signal devices

.

Pyrotechnic and non-pyrotechnic equipment m

ust be U.S

.

Coast Guard approv

ed, in serviceab

le condition and

stow

ed in a readily accessible location. Equipment pro

vid-

ing a date for ser

viceable lif

e, m

ust be within the specified

usage date as shown.

PYROTECHNIC EQUIPMENT

Pyrotechnic U.S

. Coast Guard approv

ed visual distress

signals and associated equipment include:

Red flares, hand held or aer

ial

Orange smok

e, hand held or floating

Launchers for aer

ial red meteors or parachute flares

1.19

Summary of Contents for Sport Boat Models







































































































Reviews: