background image

P A G E   9

J

L

B

B

N

P

N

P

L

LEFT

RIGHT

D

K

Q

B

F

4A

4B

6

4C

Windy conditions may affect the performance of a retractable screen.  Retract the 
screen in windy circumstances, during inclement weather, when not needed to 
support immediate ventilation or during prolong periods when not used.

CHAIN LOCK 

Position 

H-Chain Lock

 on the side wall jamb so that it rests approximately 42"  

up from the sill of the floor. Attach to the wall using 

P - #8 x 1"(25mm)  

Phillips Panhead Screws

When the screen is fully extended and being used the Pull Chain should be oper-
ated so that the screen fabric is taut in the opening and then the chain should be 
secured by the 

H-Chain Lock

.  This will help retain the screen fabric in the B-Inside 

Rails as wind hits the screen fabric.

CAUTION: Keep chain out of the reach of children at all times

.  

FOOT RELEASE LEVER 

The 

K-Foot Release Lever

 is an optional feature that makes it easier to slightly 

rotate the 

D-Pull Bar

 in order to disengage the 

L-Pull Bar Locks

 [Fig 4C] without 

bending over. Before installing, position the 

K-Foot Release Lever 

12" to 20" 

from the end of the

 D-Pull Bar 

on the side closest to the

 Pull Chain. 

Attach the

 

K-Foot Release Lever 

to the

 D-Pull Bar 

using two

 Q - #6 x 3/8” (9mm) Phillips 

Panhead Screws. 

INSTALLING SIDE RAILS 

Install the 

L-Pull Bar Locks 

at the bottom of each 

B-Inside Rail

.  Be sure that the 

L-Pull Bar Lock

 engages the 

D-Pull Bar

 as shown in image [Fig 4C]. Slide 

B-Inside 

Rails

 onto the tabs protruding from the 

F and G-Cassette End Caps

, with the 

shorter pile to the inside [Fig 4D]. Use an 1/8” drill bit and first drill through both 
sides of the 

B-Inside Rails

 where they are to be fastened. Next, using a 3/8” bit, 

drill through the outside face only. This will allow you to snap the 

N-Screw Cover 

Caps

 in place. Square and attach 

B-Inside Rails

 with 

P - #8 x 1”(25mm) Phillips 

Panhead Screws

N-Screw Cover Caps

Using the height adjustment wheel on the 

L-Pull Bar Lock

, adjust the height to 

the appropriate level so that it easily engages the 

D-Pull Bar

.  When correctly 

adjusted the latching and unlatching should be smooth and easy. 

Shorter Pile

4D

That’s it. Enjoy your new retractable screen!

ESCAPE 800

 INSTALLATION INSTRUCTIONS

SURFACE INSTALLATION

Summary of Contents for ESCAPE 800











Reviews: