background image

P A G E   5

CHAIN LOCK 

Position 

H-Chain Lock

 on the side wall jamb so that it rests approximately 42"  

up from the sill of the floor. Attach to the wall using 

P - #8 x 1"(25mm)  

Phillips Panhead Screws

When the screen is fully extended and being used the Pull Chain should be 
operated so that the screen fabric is taut in the opening and then the chain 
should be secured by the 

H-Chain Lock

.  This will help retain the screen fabric in 

the B-Inside Rails as wind hits the screen fabric.

CAUTION: Keep chain out of the reach of children at all times

.  

FOOT RELEASE LEVER 

The 

K-Foot Release Lever

 is an optional feature that makes it easier 

to slightly rotate the 

D-Pull Bar

 in order to disengage the 

L-Pull Bar 

Locks

 [Fig 4C] without bending over. Before installing, position the 

K-Foot Release Lever 

12" to 20" from the end of the

 D-Pull Bar 

on 

the side closest to the

 Pull Chain. 

Attach the

 K-Foot Release Lever 

to the

 D-Pull Bar 

using two

 Q - #6 x 3/8” (9mm) Phillips  

Panhead Screws. 

LEFT

RIGHT

B

L

C

B

L

C

J

D

K

Q

B

F

4A

4B

4C

6

Windy conditions may affect the performance of a retractable screen.  Retract the 
screen in windy circumstances, during inclement weather, when not needed to 
support immediate ventilation or during prolong periods when not used.

INSTALLING SIDE RAILS 

Install the 

L-Pull Bar Locks 

at the bottom of each 

B-Inside Rail

.  Be sure that the 

L-Pull Bar Lock

 engages the 

D-Pull Bar

 as shown in image [Fig 4C]. Slide both 

C-Outside Rails

 onto the tabs protruding from the 

F and G-Cassette End Caps 

[Fig 4A]

. Attach to jamb with 

P - #8x1”(25mm) Panhead Screws

. Press 

B-Inside 

Rails

 into 

C-Outside Rails

 with the shorter pile to the inside [Fig 4D] until they 

are evenly seated 

[Fig 4B]

.

Using the height adjustment wheel on the 

L-Pull Bar Lock

, adjust the height to 

the appropriate level so that it easily engages the 

D-Pull Bar

.  When correctly 

adjusted, the latching and unlatching should be smooth and easy. 

Shorter Pile

4D

That’s it. Enjoy your new retractable screen!

ESCAPE 800

 INSTALLATION INSTRUCTIONS

RECESS INSTALLATION

Summary of Contents for ESCAPE 800











Reviews: