background image

Environmental 

Operating temperature 

-40℉ ~ 158℉ / -40℃ ~ +70℃

Storage temperature 

-49℉ ~ 185℉ / -45℃  ~  +85℃

IP rating – Thermal camera 

IP67 

IP rating – AI Module 

IP50 

Thermal imager measurements 

Dimension ( L×W×H ) 

 3” x  2.3” x  2.7”  / 75 mm. x 58 mm. x 68 mm. 

Weight 

18 oz / 500 g. (excluding harness) 

Operating Range 

Object 

Human 

Full size car 

Detection range (under 
normal weather conditions) 

≥650 ft. / 200 m. 

≥1300 ft. / 400 m. 

Identification range (under 
normal weather condition) 

≥325 ft. 100 m. 

≥500 ft. / 150 m. 

MOUNTING INSTRUCTIONS - SPOTLIGHT

 

Portable Mount 

1.  Select the best location for mounting the spotlight.  Make sure the metal area under the magnetic base is flat and

clean to ensure a strong bond.

2.  Aluminum vehicles will require a magnetic base.  Visit our web store at https://www.larsonelectronics.com/

Permanent Mount

1.

 Determine the location for the light on your vehicle. This should be a flat surface.  The small arrow on the base

 

indicates the normal forward direction of the light. The light will rotate to the left of this arrow 185 degrees and to the

 

right 185 degrees. The lamp will tilt down 45 degrees and tilt up 90 degrees. The location should take into

 

consideration this range of motion to maximize usability.  Keep in mind the swing diameter is 286 mm (11.3 inches)

 

from the center of the mounting plate. This allows for clearance as the light is rotating. 

2.

 Remove the dog point screw from the mounting plate. Refer to Figure 1. Save this screw for reinstallation. Remove

 

mounting plate from base.

3.

 The mounting plate is designed to be mounted with either the supplied sheet metal screws or a combination of cap

 

screws, nuts and washers. You should choose hardware appropri-ate to the surface to which you intend to attach the

 

light. Drill holes in mounting surface for either type of hardware depending upon your preference

Refer to Figure 2 for hole pattern dimensions or use the mounting plate as a template.  Drill holes and secure mounting 

plate with fasteners.

RCL-336

Larson Electronics, LLC

 

 Phone: (800) 369-6671 

Fax: (903) 498-3364 

www.larsonelectronics.com 

3

 of 

1

0

 

Summary of Contents for RCL-336











Reviews: