background image

IND-SFC Series

 

Wiring Precaution 

Whether the capacity of the frequency converter in accordance with your loads.

Whether the frequency converter damaged during transportation, if so, do not connect it to power source.

Shut down power before wiring, check the input voltage before installation.

Make sure the specification of the cable in accordance with the frequency converter before wiring. The

 

cable diameter should follow the voltage level and capacity of the frequency converter.

Please refer to electrician wiring regulations, or following the "Cable Diameter Reference" table.

Avoid sharing the power switch of the frequency converter with other appliances.

Use O-type wiring terminals, make sure it's well-wired, tighten screws to avoid poor contact and prevent

 

electric shock.

Make sure the power source is correct to match single phase or three phase frequency converter.

For grounding, refer to the next page.

Make sure all switches on "OFF" status before connecting the frequency converter to power source.

Make sure the power source, frequency converter and loads are matching before power on.

Internal semiconductor components are sensitive to static electricity, be careful in touching the metal

 

control panel.

Larson Electronics, LLC

 

Phone: (877) 348-9680

 Fax: (903) 498-3364 

  www.larsonelectronics.com 

Grounding System 

In addition to safety consideration, well-grounded system also can avoid the power system interferes

 

equipment normal operation.

Ground Cable should be separated with Neutral Cable, unless special applications.

Ground Cable should be 8AWG cable at least or the diameter is basically the same.

Ground Cable is for specified frequency converter only, poor ground will cause interference to other

 

machines.

Use ground rods in grounding for the best.

Ground Types:

tem Applica

tion

Item

Resistance value

Low voltage power supply system or high voltage electrical 
equipment of three-phase four-wire multi-grounded systems 
grounding  

10

 or less 

Ungrounded high-voltage electrical equipment grounding 
system. 

25

 or less 

Low voltage power supply system of three-phase three-wire 
ungrounded system. 

50

 or less 

1.. round voltage less than 150V is 100

 or less.

2.. round voltage 151V to 300V is 50

 or less.

3.. round voltage higher than 301V is 10

 or less.

1. 

Low voltage electrical equipment grounding

2. 

Inner system grounding

3. 

Frequency converter secondary grounding

4. 

Low voltage electrical equipment metal body 

grounding.

Summary of Contents for IND-SFC Series


















Reviews: