4
www.
larsonelectronics.com
Specifications
Camera
IDCMR-IP-POE-DMIP
Image Sensor:
1/2.9” Progressive Scan CMOS
Signal System:
NTSC
Min. Illumination:
Color: 0.01 lux @(F1.2, AGC ON),
0 lux with IR
Shutter time:
1/3 s to 1/100,000 s
Slow shutter:
Support
Lens:
2.8 mm, horizontal field of view: 80°
Iris
F2.0
Lens Mount:
M12
Adjustment Range:
Pan: 0° ~ 355°, tilt: 0° ~ 75°, rotate: 0° ~ 355°
Day& Night:
IR cut filter
Wide Dynamic Range:
120 dB
Digital noise reduction:
3D DNR
Compression Standard
Video Compresion
Main stream: H.265 / H.264
Sub stream: H.265 / H.264 / MJPEG
Third stream: H.265 / H.264
H.264 Type
Main Profile / High Profile
H.264+
Supports
H.265 Type
Main Profile
H.265+
Supports
Video bit rate:
32 Kbps ~ 16 Mbps
Image
Max. Image Resolution:
2560 × 1920
Main Stream:
20 fps (2560 × 1920),
30 fps (2560 × 1440, 2048 × 1536, 1920 × 1080, 1280 ×720)
Sub Stream:
30 fps (640 × 360, 352 × 240)
Third Stream:
30 fps (1280 ×720, 640 × 360, 352 × 240)
Image Enhancement:
BLC/3D DNR
Image Settings:
Rotate Mode, Saturation, Brightness, Contrast, Sharpness adjustable by client software or
web browser
Region of Interest (ROI):
Support 1 fixed region for mainstream and sub stream separately
Day/Night Switch:
Auto / Scheduled / Alarm Triggered
Network
Network Storage
Support microSD / SDHC / SDXC card up to 128GB local storage, NAS (NFS, SMB / CIFS), ANR
Alarm Trigger
Motion Detection, Tampering Alarm, Network Disconnected, IP Address Conflict, Illegal Login,
HDD full, HDD error
Protocols:
TCP/IP, UDP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, PPPoE, NTP, UPnP,
SMTP, SNMP, IGMP, 802.1X, QoS, IPv6
General Functions
One-key reset, anti-flicker, heartbeat, mirror, password protection, privacy mask, Watemark,
IP address filtering
System Compatibility:
ONVIF (Profile S, Profile G), PSIA, CGI, ISAPI
Interface
Communication
Interface:
1 RJ45 10M/100M self-adaptive Ethernet interface
In-camera storage:
Built-in microSD / SDHC / SDXC slot, up to 128GB
Smart Features
Behavior Analysis
Line crossing detection, Intrusion detection, Unattended baggage detection, Object removal
detection
Line Crossing Detection
Cross a pre-defined virtual line, up to 1 pre-defined virtual line supported
Intrusion Detection
Enter and loiter in a pre-defined virtual region, up to 1 pre-defined virtual regions supported
Unattended Baggage
Objects left over in the pre-defined region such as the baggage, purse, dangerous materials
Object Removal
Objects removed from the pre-defined region, such as the exhibits on display.
Face Detectionn
Human face appears in the image can be detected and trigger linkage method
General
Operating Conditions:
-22 °F ~ 140 °F (-30 °C ~ 60 °C), Humidity 95% or less (non-condensing)
Power Consumption:
12 Vdc ± 25%, 6.2 W,
PoE (802.3af, 42.5 ~ 57V, class 3), 9 W
Weather Proof:
IP67, IK10
Camera
IDCMR-IP-POE-DMIP
IR Range:
Up to 120 ft (approx. 35 m)
Dimensions:
Camera
: Φ4.4” × 3.2” (Φ111 × 82.4 mm)
Package
: 5.27” × 5.27” × 4.25” (134 × 134 × 108 mm)
Weight:
Camera
: 1.1 lb (500 g)
Using the Waterproof Ethernet Fitting
Install the
Waterproof Ethernet Fitting
on the Enternet cable end at the camera when moisture
or contamination exists in the area near the caemra. The fitting includes several parts that must be
installed in a specific order. To install the fitting:
1.
Place the rubber O-ring over the camera drop cable end cap.
Push the O-ring up to the connector cap.
2.
If an RJ-45 connector is installed on the network cable, from
the router or switch, remove it.
3.
Place the Lock Nut onto the network cable from the router
or switcn as shown in the drawing to the right. The inside
threads must be toward the camera end.
4.
Place the rubber basket onto the network cable above the lock
nut as shown.
5.
Place the end cap onto the network cable above the rubber
gasket as shown. The fingered end must be toward the the
router or switch.
6.
Install an RJ-45 connector onto the network cable.
7.
Plug the RJ-45 connector with the network cable into the
camera network drop cable.
8.
Fit the end cap on the network cable onto the camera drop
cable end cap. Rotate the network cable end cap to lock it in
place.
9.
Push the rubber gasket fully into the end of the network cable
end cap.
10. Screw the lock nut onto the network cable end cap until it is
fully seated.
Network drop
cable from
camera
Network cable from
router or switch
Fitting assembled
Waterproof Ethernet Fitting assembed and connected
Drop cable
end cap
Network drop
cable from
camera
Rubber
O-ring
seal
RJ-45
connector
End cap
Rubber
gasket
Network
cable
from
router or
switch
Lock nut
