The
GL-30004-S
-E
36
Watt motorized spot light
combo
that operates with a wireless hand held remote
control and a wireless dash mount remote control.
This particular model is available in a white finish and
is mounted on a stanchion post with red/green
navigational running lights. It produces a wide spot
beam with an effective working beam of 700 feet and
has a 5 million candlepower rating.
GL-2100 Hard Wired - Permanent Mount:
GL-30004-S
-E
Searchlight
Wireless Remote Control
2 A23 12V Batteries
Perko Socket/Mount
MOUNTING INSTRUCTIONS
Determine the location for the light on your vehicle or
boat. The small arrow on the base indicates the
normal forward direction of the light. The light will
rotate to the left of this arrow approximately 185 and
to the right approximately 185. The beam will angle
down about 45 and angles up to 90. The location
should take into consideration this beam movement
to ensure optimum usability.
Once the position and orientation are decided
upon
—use the black rubber gasket as a footprint to
mark the mounting of base to vehicle. Drill 1/4 inch
hole though mounting surface in the middle of the
footprint for passage of the power cord. Use silicone
sealant to fill opening around power cord.
IMPORTANT: Allow
3” of cord to remain under the
light to ensure full 370 rotation.
You should choose screw or bolt fasteners
appropriate to the surface to which you intend to
attach the light. If you intend to use the four small
plastic caps provided to cover the screw heads once
installed, a #8 round head is recommended.
The black gasket should be installed on the lamp
base prior to attachment to the vehicle surface.
NOTE: The small drain hole in the edge of the
gasket should normally face opposite the forward
direction of the vehicle
—opposite the arrow molded
in the front of the base. Silicone or other like
sealants should not be used around the base gasket
as it will limit the light’s ability to drain excess water
properly.
The 12 Volt DC power wire should be joined to the
leads under the lamp with appropriate automotive
wire attachments. It is critical that polarity be
observed. Connect vehicle positive (+) to spotlight
positive (+) wire. Connect vehicle ground (-) to
spotlight ground (-) wire. Power should be fused at
10 Amps and be on a dedicated circuit, or wired to an
appropriate automotive relay system.
PROGRAMMABLE REMOTE INSTRUCTIONS
The
GL-30004-S
is controlled with a
programmable remote with 2187 different
channels. This feature allows you the freedom to
change the channel selection, and the receiver
relearns the new selection.
PROGRAMMING THE TRANSMITTER.
This light has been pre-programmed at the factory, it
is not necessary to re-program the transmitter, but is
recommended.
PROGRAMMABLE REMOTE INSTRUCTIONS
The
GL-30004-S
Light is controlled with a
programmable remote with 2187 different channels.
This feature allows you the freedom to change the
channel selection, and the receiver re- learns the
new selection. This light has been pre-programmed
at the factory, and it is not necessary to re-program
the transmitter, unless you experience outside
interference. To program transmitter:
1. IMPORTANT
Disconnect power.
2.
Remove battery cover from remote control.
3.
Set the 7 dip switches to a selection of your
choice. There are 3 positions on each; positive,
negative and neutral. Use a small screwdriver and
select a position for each dip switch. *Please note
that the orientation of the +/- switch positions may
vary among different models of wireless remote
controls.
4.
Insert both A23 12V batteries. Be sure batteries
have adequate charge.
5.
Replace battery cover.
a.
Depress the on/off button and hold it down.
Red LED will light.
b.
While holding the on/off button down,
reinstall the power (replace fuse or connect
vehicle battery).
c.
Keep on/off button depressed for 5-6
seconds, and then release. The light should
now be programmed.
