background image

 

Larson Electronics, LLC

 

 Phone: 

877-348-9680

 

Fax: (903) 498-3364 

www.larsonelectronics.com 

Explosion Proof Warnings (General) 

WARNING 

TO AVOID THE RISK OF FIRE, EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED, 

INSPECTED AND MAINTAINED  BY A QUALIFIED  ELECTRICIAN  ONLY,  IN  ACCORDANCE  WITH ALL 

APPLICABLE ELECTRICAL CODES. 

TO AVOID ELECTRIC SHOCK: 

BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

PRODUCT  MUST  BE  CONNECTED TO A  WIRING  SYSTEM  WITH  AN  EQUIPMENT-GROUNDING

CONDUCTOR.  

TO AVOID EXPLOSION: 

MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.

ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS

ATMOSPHERE.

DO  NOT  OPERATE  IN AMBIENT  TEMPERATURES  ABOVE  THOSE  INDICATED  ON  THE PRODUCT

NAMEPLATE.

DO  NOT  OPERATE  IF THE  LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED  OR

DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.

ALL FASTENERS SHOULD BE PROPERLY SEATED.

2

 of 

7

 

Larson Electronics LLC Earth Tag Size 

Short Circuit Ratings Symmetrical Fault Current 

(kA) for 1 second 

20 

3.06 

25 

4.06 

32 

5.40 

40 

7.20 

50 

10.40 

63 

10.40 

75 

10.40 

Earth Tag Rating Table

CGB-C1D1-MCHL

 Series

 

Summary of Contents for CGB-C1D1-MCHL Series









Reviews: