background image

www.lanpro.com

Wireless - Equipment - 2.4 GHz - LP-1521 User Manual High Speed Long Range Wireless Broad Band Router, with PoE

 Trademarks

Copyright @2009 

Contents are subject to change without notice.

All trademarks belong to their respective proprietors.

2

Copyright Statement

THIS DOCUMENT CONTAINS OF PROPRIETARY TECHNICAL INFORMATION THAT IS THE PROPERTY OF THIS 

COMPANY. AND NO PART OF THIS DOCUMENTATION MAY BE REPRODUCED, STORED IN A RETRIEVAL SYSTEM 

OR  TRANSMITTED  IN  ANY  FORM  OR  BY  ANY  MEANS,  ELECTRICAL  OR  MECHANICAL,  BY  PHOTOCOPYING, 

RECORDING, OR OTHERWISE, WITHOUT THE PRIOR WRITTEN CONSENT OF THIS COMPANY.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of 

the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a residential 

installation.    This  equipment  generates,  uses  and  can  radiate  radio  frequency  energy  and,  if  not  installed  and  used  in 

accordance with the instructions, may cause harmful interference to radio communications.  However, there is no guarantee 

that interference will not occur in a particular installation.  If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct 

the interference by one of the following measures:

 

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device 

may not cause harmful interference, and (2) this device must accept any interference received, including interference that 

may cause undesired operation.

 

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the 

user’s authority to operate this equipment.

 

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This  equipment  complies  with  FCC  radiation  exposure  limits  set  forth  for  an  uncontrolled  environment.  This  equipment 

should be installed and operated with minimum distance 20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

 

Summary of Contents for LP-1521









































Reviews: