manualshive.com logo in svg

Lanner HCP-72i1, User Manual

Share
Download
Lanner HCP-72i1 User Manual Download Page 76

76

www.lannerinc.com

Save & Exit

Use [<--] / [-->] to select [Save & Exit] setup screen. Under this screen, you may use [

↑] [↓] 

to select an item you 

want to configure. 

Save Changes and Exit: 

exit system setup after saving the configuration changes

Discard Changes and Exit: 

exit system setup without saving the configuration changes

Save Changes and Reset

: reset the system after saving the configuration changes

Discard Changes and Reset

: reset the system without saving the configuration changes

Save Options
Save Changes

: save the configuration changes

Discard Changes

: discard all the configuration changes

Restore Defaults

: restore to factory default setting

Save as User Defaults

: save changes as the new user default

Restore User Defaults

: restore the user default

Boot Override
Launch EFI Shell from filesystem device

: launch Extensive Firmware Interface which will allow you to input Shell 

commands

Summary of Contents for HCP-72i1





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands