manualshive.com logo in svg

Lanier R/C Stinger 60, Manual, Page: 14 / 16

Share
Download
Lanier R/C Stinger 60 Manual Download Page 14

 

LANIER  R/C 

HARDWARE AND MATERIAL LIST TO FINISH THE STINGER 60 

GENERAL 
 

1.   4 - Cannel radio with four standard servos 
2.   Engine size - .51 - .75 two cycle, .60 - .90  four cycle 
3.   Fuel line - medium 
4.   Propellor - depending on engine size. 
5.   3" spinner - Tru-Turn or Du-Bro 
6.   Fuel tank - Du-Bro 10 - 14 oz 
7.   Covering, paint and trim - your choice 
8.   Wheels - Du-Bro 3.00L (3") 
 

FUSELAGE 
 

1.   Engine mount - Hayes KM 70 
2.   Mounting bolt set - Du-Bro # 130  (engine mounting) 
3.   #10 -32 x 7/8" bolt (2) (landing gear mounting) 
4.   #10 Fender Washer (2) (landing gear mounting) 
5.   #10 - 32 Self looking nut (2) 
6.   5/32" Wheel collars (4) Du-Bro #140 (landing gear) 
7.   Steel axle (2) Du-Bro #248 (landing gear) 
8.   #6 "All Threads" insert (9) Ohio Superstar  (cowl, wheel pants, wing cover) 
9.   #6 Button head screw (9) Du-Bro #530 (cowl, wheel pants, wing cover) 
10. #6 Nylon Washer (7)  (cowl, wing cover) 
11. 1/4-20 x 1-1/4" nylon bolt (2) (wing hold down) 
12. Nylon kwik-link with rod (3) Du-Bro #229 (fuselage pushrods) 
13. Dave Brown pushrod system (fuselage pushrods) 
14. Engine control flex-cable assembly  Du-Bro # 165  
 

WING 
 

1.   Kwik-link with rod (2) Du-Bro #306 (2) (aileron pushrod) 
2.   Hinge point (10) Robart # 308 (aileron hinges) 
3.   Control horn (2) Robart #325 (ailerons) 

 
TAIL ASSEMBLY 
 

1.   Control horn (2) Robart #325 (rudder and elevator) 
2.   Hinge point (10) Robart #308 (rudder and elevator) 
3.   3/32" wheel collar (1) Du-Bro #138 (tailwheel retainer) 
4.   1-1/4" dia tailwheel (1) Du-Bro #125TW 
5.   Landing gear straps (8) Du-Bro #158 
6.   Kwik-Link with rod (4) Du-Bro #229 
7.  Solder Kwik-Link (4) Du-Bro #603 
8.  #2 Lock Nut (3) Du-Bro #168 
9.  #2 X 3/4" screw (3) Du-Bro #311 
 

 

 

 
 
 
 
 
 

                                                                                          
                                                                      

1995 Lanier R/C Inc. 

14 

Summary of Contents for Stinger 60

















Reviews:

No comments