background image

7

 

UNPACKING 

Receiving the Melter 

Upon receipt, check for freight damage, both visible and concealed.  Visible 
damage should be noted on the freight bill at the time of delivery and signed by the 
carrier's agent.  Concealed loss or damage means loss or damage, which does not 
become apparent until the merchandise has been unpacked.  If concealed loss or 
damage is discovered upon unpacking, make a written request for inspection by the 
carrier's agent within 15 days of delivery.  All packing material should be kept for 
inspection.  

Do not return damaged merchandise to Lang Manufacturing 

Company.  File your claim with the carrier.

 

Location 

Prior to un-crating, move the melter as near to its intended location as practical.  
The crating will help protect the unit from the physical damage normally associated 
with moving it through hallways and doorways. 

Un-crating 

The melter will arrive completely assembled inside a wood frame and strapped to a 
skid.  

Cut the straps and remove the wood frame.   

CAUTION:

 

THE UNIT IS EXTREMELY HEAVY.  FOR SAFE 
HANDLING, INSTALLER SHOULD OBTAIN HELP AS 
NEEDED, OR EMPLOY APPROPRIATE MATERIALS 
HANDLING EQUIPMENT (SUCH AS A FORKLIFT, 
DOLLY, OR PALLET JACK) TO REMOVE THE UNIT 
FROM THE SKID AND MOVE IT TO THE PLACE OF 
INSTALLATION.

 

CAUTION:

 

ANY STAND, COUNTER OR OTHER DEVICE ON WHICH 
THE MELTER WILL BE LOCATED MUST BE DESIGNED 
TO SUPPORT THE WEIGHT OF THE MELTER.

 

CAUTION:

 

SHIPPING STRAPS ARE UNDER TENSION AND CAN 
SNAP BACK WHEN CUT.

 

Remove the Melter from skid and place in intended location. 

 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

Summary of Contents for MM24



















Reviews: