![background image](http://html1.mh-extra.com/html/lang/ecco-t/ecco-t_service-manual_3564747007.webp)
6
INSTALLATION
RECEIVING THE OVEN
Upon receipt, check for freight damage, both visible and concealed. Visible damage should be noted on the
freight bill at the time of delivery and signed by the carrier's agent. Concealed loss or damage means loss
or damage, which does not become apparent until the merchandise has been unpacked.
If concealed loss or damage is discovered upon unpacking, make a written request for inspection by the
carrier's agent within 15 days of delivery. All packing material should be kept for inspection.
Do not return damaged merchandise to Lang Manufacturing Company. File your claim with the carrier.
Prior to un-crating, move the oven as near its intended location as practical. The crating will help protect
the unit from the physical damage normally associated with moving it through hallways and doorways.
LEG INSTALLATION
Legs are available for both the single and double deck installations. Single deck installations require a 27-
inch leg. Double deck installations require 6-inch legs or casters.
To install the 27-inch legs, place some cardboard on the floor and gently tip the oven onto its back. Fasten
two legs to the oven's front corners using the four 5/16 inch bolts provided in the leg kit. Lift the oven onto
its front legs and block the back up using one of the 27-inch legs set upside down in the center rear of the
oven body. Install the last 27-inch leg onto the oven body on the control side rear. Gently lift the oven
rear, remove the leg set to support the oven center and install it on the last rear corner.
To install the 6-inch legs or casters, attach the leg or caster to the leg supports supplied in the oven by
following the instructions in the box, then attach the leg support to the oven.
The adjustable feet on the bottom of each leg may be screwed in or out as necessary to level the oven.
STACKING THE OVENS
Remove all the plug buttons from the top of the lower oven.
Remove the stacking kit from the oven compartment of one oven and install the 1 1/4-inch plastic bushing
into the top of the lower oven.
Tip the top oven backwards and install two 3/8-inch socket head bolts, found in the stacking kit, into the
two front leg holes that match the holes in the top of the lower oven. Install the socket head bolts with the
heads of the bolt pointing away from the oven.
Lift the top oven and gently set on top of the lower oven so that the heads of the socket head bolts nest into
the holes in the top of the lower oven.
ELECTRICAL CONNECTION
The electrical service entrance is provided by a 1 1/4-inch knockout in the bottom right front corner of each
oven, or at the oven back directly behind the control compartment. Grounding lugs are provided at both the
front and rear service entrances.
The 208/240-volt oven is a dual voltage oven and is shipped from the factory as 208 volt. The oven must
be field converted to operate on a 240-volt power supply.
To convert the oven to 240 volt, remove the jumper wire located on a terminal strip located inside the lower
portion to the control compartment. On newer oven a toggle switch is provided at the back of the unit for
this purpose.
With 480-volt installations check to be sure that the motor rotates in a clockwise direction as viewed from
the front of the oven.
To reverse the motor rotation, switch any two incoming power supply leads and recheck the rotation.
Supply wire size must be large enough to carry the amperage load for the number of ovens being installed.
Wire size information can be found on the oven DATA PLATE.
This oven can be installed on both single and three phase supplies and is shipped from the factory for three
phase.
To phase the oven to match the power supply, follow the charts in the Technical Data portion of this
manual or to the wiring diagram for proper wire size and grouping.
Summary of Contents for ECCO-T
