![background image](http://html1.mh-extra.com/html/lang/ecco-t/ecco-t_service-manual_3564747015.webp)
14
PROGRAMMING TERMS
CONTROL PANEL BUTTONS
1 -0
Product Buttons. These are the buttons where the product programs are stored.
Pressing a Product Button will heat the oven to the programmed temperature.
A - E
Shelf Buttons. The control is capable of timing each shelf individually. Pressing a
Product Button then a Shelf Button will start the countdown timer.
Man Prog
The MANUAL PROGRAM button allows the operator to enter a temporary
product program without being required to input the programming code. The
temporary program is erased when the oven is turned off or when a new program is
entered. Time and temperature are the only parameters that can be entered in the
Manual Program mode.
READ/CLEAR
The READ/CLEAR button has several functions.
It is always the first button pressed when entering programming codes.
Pressing it twice then pressing a Product Button will "read-back" the program
in that product button.
Pressing and holding the button down until "
88888
" appears in the display will
cancel the current mode of the control and return the display to "
Enter
".
Temp
When the Temperature Recall Button is pressed, the display will indicate the
internal oven temperature. When released the display will revert to the previous
readout.
PROGRAMMING TERMS
COOKING CURVE
Cooking curve is a function of the computer that controls the cooking time. If the
temperature of the oven is lower than the programmed temperature, the control will
slow the timer down to compensate for the lower cooking temperature. Cooking
Curves from 0 - no time adjustment to 7 - maximum adjustment are available.
Cooking Curve 3 is the most commonly used. However, as a general rule the
longer the cooking time the lower the cooking curve, the shorter the cooking time
the higher the cooking curve.
FAN FUNCTION
The convection fan has two programmable options. Fan On (Fan 1) runs the
convection fan continuously. Fan Off (Fan 0) leaves the fan off until heat is called
for by the control. In a convection oven, the fan must come On whenever the heat
comes On. The convection fan cannot be turned Off continuously.
TIER
"Tiered" programming is the ability to change the cooking temperature or fan
function during the cooking cycle. As an example, some products require the fan
to be Off for the first half of the cooking cycle then turn On for the last half, Tier 1
would be programmed with the fan in the Off mode then Tier 2 would be fan On.
The Tier lamps located below the display (labeled T1, T2, T3, and T4) will
illuminate to indicate which Tier is being programmed or which Tier the program
is in during the cooking cycle.
Summary of Contents for ECCO-T
