background image

6

CAUTION

UNPACKING

Receiving the Griddle

Upon receipt, check for freight damage, both visible and concealed.   

Visible damage should be noted on the freight bill at the time of delivery and 

signed by the carrier’s agent.  Concealed loss or damage means it does not 

become apparent until the merchandise has been unpacked.  If concealed 

loss or damage is discovered upon unpacking, make a written request for 

inspection by the carrier’s agent within 15 days of delivery.  All packing  

material should be kept for inspection.  

DO NOT return damaged 

merchandise to Lang Manufacturing.  File your claim with the carrier.

Location

Prior to un-crating, move the griddle as near to its intended location as practical. The crating will help 

protect the unit from the physical damage normally associated with moving it through hallways and 

doorways.

Un-crating

The griddle will arrive completely assembled inside a wood frame and strapped to a skid.  

Cut the straps and remove the wood frame.  
The griddle can now be removed from the skid.

THE UNIT IS EXTREMELY HEAVY.  FOR SAFE HANDLING, INSTALLER SHOULD 

OBTAIN HELP AS NEEDED, OR EMPLOY APPROPRIATE MATERIALS HANDLING 

EQUIPMENT (SUCH AS A FORKLIFT, DOLLY, OR PALLET JACK)  

TO REMOVE THE UNIT FROM THE SKID AND MOVE IT TO THE PLACE OF  

INSTALLATION.
ANY STAND, COUNTER OR OTHER DEVICE ON WHICH GRIDDLE WILL BE  

LOCATED MUST BE DESIGNED TO SUPPORT THE WEIGHT OF THE GRIDDLE.
SHIPPING STRAPS ARE UNDER TENSION AND CAN SNAP BACK WHEN CUT.

LEG INSTALLATION

The legs are installed by sliding the threaded ends of the 

legs into the leg receiver tubes located in each corner of 

the griddle.
Slide the leg up until contact is made with the threaded 

nut at the top of the reciever tube.  Screw the leg counter-

clockwise until it is hand tight.
After the griddle is in its final position, adjust the legs to 

create 1/8 inch slant from back to front. This will allow the 

grease to run into the front grease gutter and provide the 

proper combustion air for the burners.  It will also allow 

exposed gasses to escape out the rear of the unit.  
Level unit by adjusting the (4) legs for accurate and perfect 

lineup with other units. 

Front

IL2379

Summary of Contents for 224ZT

























Reviews: