background image

2M-W358; 

ACCU-TEMP

 Spark Ignition Gas Griddle

2M-W358; 

ACCU-TEMP

 Spark Ignition Gas Griddle

8

INSTALLATION

Electrical Connection

The griddle is supplied with a cord and plug.  The receptacle is not provided with the griddle. 
Follow the receptacle manufacturer’s instructions when connecting the receptacle to the power supply.

Gas Connection

This griddle is manufactured for use with the type of gas indicted on the nameplate.  

 

Contact the factory if your type of gas does not match the nameplate data.
All gas connectors must be in accordance with local codes and comply with the National Fuel Federal 

Gas Codes ANSI Z223.1 latest edition.
This appliance should be installed with a separate gas valve in the gas line ahead of the unit. Use a 

3/4 inch or larger gas supply line.

Remove

 the 5/16 inch nuts securing the rear of burners.  These nuts are for securing the main burners 

during transportation only.  The rear burner shield must be removed to gain access to the nuts.
A pressure regulator for the type of gas specified is supplied with each appliance.

This regulator must be installed in the gas supply line.

  (Note the direction of the gas flow arrow.)  

The pressure in the manifold of the appliance should be tested with a manometer and the regulator 

adjusted for proper pressure with the appliance operating at full fire.  A 1/8 inch NPT tap is provided in 

the manifold for connecting a manometer.
Correct manifold pressures are:

 

5 inches water column for natural gas

 

10 inches water column for propane

When replacing the plug in the manifold, a pipe joint compound or sealant should be used that is 

resistant to the action of liquid petroleum gas.
Initial adjustments are the responsibility of the installer and are not chargeable to Star Manufacturing 

International.
After the griddle is in its final position, adjust the legs to create 1/8 inch slant from back to front.  

This will allow the grease to run into the grease gutter and provide the proper combustion air for the 

burners.

DANGER:  THIS APPLIANCE MUST BE GROUNDED AT THE TERMINAL 

PROVIDED.  FAILURE TO GROUND THE APPLIANCE COULD 

RESULT IN ELECTROCUTION AND DEATH.

 

INSTALLATION OF THE UNIT MUST BE DONE BY PERSONNEL 

QUALIFIED TO WORK WITH ELECTRICITY AND PLUMBING.  

IMPROPER INSTALLATION CAN CAUSE INJURY TO PERSONNEL 

AND/OR DAMAGE TO EQUIPMENT.  UNIT MUST BE INSTALLED IN 

ACCORDANCE WITH ALL APPLICABLE CODES.

NOTICE: 

The data plate is located inside the control compartment of each 

griddle. The griddle voltage, serial number, gas specifications, and 

clearance specifications are on the data plate.  This information 

should be carefully read and understood before proceeding with 

the installation.

NOTICE: 

The installation of any components such as a vent hood, grease 

extractors, fire extinguisher systems, must conform to their 

applicable National, State and locally recognized installation 

standards.

WARNING

Summary of Contents for 224T





























Reviews: