background image

12 

Cleaning

WARNING 

KEEP WATER AND SOLUTIONS OUT OF CONTROLS.  NEVER 
SPRAY OR HOSE CONTROL CONSOLE, ELECTRICAL 
CONNECTIONS, ETC. 

 

CAUTION 

MOST CLEANERS ARE HARMFUL TO THE SKIN, EYES, MUCOUS 
MEMBRANES AND CLOTHING. PRECAUTIONS SHOULD BE 
TAKEN TO WEAR RUBBER GLOVES, GOGGLES OR FACE 
SHIELD AND PROTECTIVE CLOTHING.  CAREFULLY READ THE 
WARNING AND FOLLOW THE DIRECTIONS ON THE LABEL OF 
THE CLEANER TO BE USED

.

 

 

  Always start with a cold griddle. 

  The stainless exterior can easily be cleaned using a good non-abrasive cleaner. 

  Always follow the cleaner manufacturer's instructions when using any cleaner. 

  Always apply these cleaners when the griddle is cold and rub in the direction of the 

metal's grain. 

  At least once a day, remove the waste drawer and wash in the same way as an ordinary 

cooking utensil. The drawers are removed by pulling forward until they are released from 
their track. 

 

Griddle Surface Care (non-chromium surfaces) 

It takes very little time and effort to keep the griddle attractive and performing at top efficiency. 
If grease is permitted to accumulate, it will form a gummy cake and then carbonize into a hard 
substance which is extremely difficult to remove. To prevent this condition, the following 
suggestions for cleanliness should be followed: 

After each use, scrape the griddle with a scraper or flexible spatula to remove excess grease 
and food. A waste drawer is provided for the scrapings. If there is an accumulation of burned 
on grease and food, the griddle should be thoroughly scoured and seasoned. Use pumice or 
griddle stone while the griddle is warm.  

Do not use steel wool because of the danger of steel slivers getting into the food. 

 

 

 
 
 

Summary of Contents for 124S-M





















Reviews: