Lang 124CMW Assembly, Installation And Operation Instructions Download Page 13

13

MAINTENANCE & CLEANING

WARNING: KEEP WATER AND SOLUTIONS OUT OF CONTROLS. NEVER 

SPRAY OR HOSE CONTROL CONSOLE.

CAUTION:

MOST CLEANERS ARE HARMFUL TO THE SKIN,

EYES, MUCOUS MEMBRANES AND CLOTHING.

PRECAUTIONS SHOULD BE TAKEN TO WEAR

RUBBER GLOVES, GOGGLES OR FACE SHIELD AND

PROTECTIVE CLOTHING. CAREFULLY READ THE

WARNING AND FOLLOW THE DIRECTIONS ON THE

LABEL OF THE CLEANER TO BE USED.

NOTICE:

Never leave a chlorine sanitizer in contact with

stainless steel surfaces longer than 10 minutes.

Longer contact can cause corrosion.

Cleaning

•  Always start with a cold melter.

•  The stainless exterior can easily be cleaned using warm water and mild 

detergent.  

Do not use caustic cleaners.

•  Always follow the cleaner manufacturer’s instructions when using any cleaner.

•  The melter rack and interior may be cleaned using warm water and mild 

detergent. 

Do not use caustic cleaners.

•  Do Not

 attempt to clean heater tubes, damage can occur from improper 

cleaning.

•  Do Not

 spray cleaning solutions into cooking chamber.

•  Always apply these cleaners when the melter is cold and rub in the direction of 

the metal’s grain.

Summary of Contents for 124CMW

























Reviews: