background image

E6

Problem

No operation for 

the pulling tool.

Stop working.

Slip between 

rope and drum.

Possible Cause

1. Power supply is not 

connected.

1. Power shortage for the 

battery pack.

2. The tractor exceeds the 

upper limit of the pull force.

1. Insufficient friction between 

rope and  drum.

Solution

1. Check battery whether there is electricity.

2. Whether the power switch is on or not.

3. The downtime is more than 10 minutes 

and need to be restarted.

1. Ensurethe full electricity.

2. Reduce the weight of the tractor and 

restart it.

1. Check whether there is oil stain on the 

rope and drum, and clean the oil stain.

2. The rope is seriously worn and need to 

replace a new one.

3. Tension the rope so that the rope is in 

full contact with the drum

WINCHING

While winching, position yourself away from the winch in order to see both the winch and the 

load. Pull HORIZONTALLY on the rope. The tension you exert on the rope will keep the winch 

Cad Pull HORIZO level.

DANGER do not wrap the rope around your handsor yur your body! alos beware of the 

rope accumulating in front of you; make sure your feet do not get tangled in it.

1. If the rope slips

If the rope on the drum while winching, add a fourth wrap of rope on the drum. When the winch 

reaches its maximum capacity, motor power-off protection. You then have to redo your set-up .

2. How to pause while winching

SLOWLY release the tension on the rope and let i slip on the capstan drum.

CAUTION do not let the rope slip for more that a few seconds on the rum while in 

tension – the heat created by the friction could melt or damage the rope.

3. Stopping the winch

1) Release tension gradually to lower the winch gently to the ground

2) Turn off the power switch

Once your job is done, you should clean and dry your winch.

CAUTION inspect the winch, hooks, rope, knots and polyester sling to detect any 

damage or signs of wear.

TROUBLE SHOOTING

Summary of Contents for LWB0301













Reviews: