manualshive.com logo in svg

Landoll Brillion SL10, Operator'S Manual

Share
Download
Landoll Brillion SL10 Operator'S Manual Download Page 9

SAFETY INFORMATION

1P342-0621

1-5

Decals

Figure 1-3:  Decals

CAUTION

BE SURE TO ENGAGE

PARKING PIN ON LEFT END OF

FRAME BEFORE UNHITCHING

TRACTOR.  OTHERWISE

FRAME WILL TIP BACKWARDS

ABOUT FRONT AXLE

9J302

WARNING

MOVING PART HAZARD

TO PREVENT SERIOUS INJURY FROM

MOVING PARTS:

  KEEP COVERS CLOSED DURING OPERATION.

  DO NOT ALLOW ANYONE TO RIDE OR CLIMB 

  MACHINE DURING OPERATION.

  KEEP OBSERVERS AWAY.

2K123

CAUTION

MOVING MACHINES CAN CAUSE INJURY.  KEEP AWAY!

1.  KEEP AWAY FROM MOVING TRACTORS OR IMPLEMENTS.

KEEP OTHERS AWAY.

2.  DO NOT RIDE OR ALLOW OTHERS TO RIDE ON TRACTOR

OR IMPLEMENT.

3.  BLOCK IMPLEMENT TO PREVENT MOVEMENT WHEN

UNHITCHED FROM TRACTOR.

4.  KEEP ALL GUARDS AND SHIELDS IN PLACE WHILE

MACHINE OR PARTS ARE IN MOTION.

8J309

WARNING

DO NOT GO NEAR LEAKS

High pressure oil easily punctures
skin causing serious injury,
gangrene or death.
If injured, seek emergency medical
help. Immediate surgery is
required to remove oil.
Do not use fingers or skin to
check for leaks.
Lower load or relieve hydraulic
pressure before loosening fittings.

PARKING PIN

9J
30
1

Turfmaker

4K401

13 TOOTH 

DRIVER

(26 TOOTH

  OPTIONAL)

37 TOOTH

DRIVEN

15/16 HEX

13 TOOTH

IDLER

TIGHTENER

6 TOOTH

#A550 DRIVER

*

*

1.  RATES ARE FOR 13 TOOTH DRIVER.  DOUBLE THESE VALUES FOR 26 TOOTH DRIVER.
2.  RATES ARE INTENDED AS A GUIDE ONLY.  VARIATIONS IN SIZE AND CLEANLINESS WILL AFFECT RATES.
     CHECK ACREAGE AND POUNDS OF SEED USED FOR BEST RESULTS.

PLANTING RATES

9J881 FOR SL8, SL10, SL12 SEEDER

* WILL CRACK SOME SEEDS AT THESE SETTINGS.
NOT RECOMMENDED:   LENTILS, SORGHUM, SUDAN GRASS

MACHINE MAY BE CALIBRATED FOR UNLISTED SEED AS FOLLOWS:

1.  REMOVE DRIVE BOLT FROM 6 TOOTH #A550 CHAIN DRIVER SPROCKET.
2.  RAISE MACHINE AND LOCK IN TRANSPORT POSITION.
3.  PLACE A CANVAS OR TARP TO CATCH SEED.
4.  TURN 15/16 HEX ON TRANSMISSION CLOCKWISE(CW) AS FOLLOWS:
      136 REVOLUTIONS FOR 8 FOOT SEEDER.
      109 REVOLUTIONS FOR 10 FOOT SEEDER.
        91 REVOLUTIONS FOR 12 FOOT SEEDER.
5.  WEIGH SEED AND MULTIPLY BY 10 (20 FOR 26TOOTH DRIVER)
     FOR APPROXIMATE PLANTING RATE IN POUNDS PER ACRE.

CALIBRATION

ITEM 5

2K123

ITEM 6

9J881

ITEM 7

8J309

ITEM 9

1-573-010006

ITEM 10

9J301

ITEM 11

2P151

ITEM 13

9J302

ITEM 12

3K706

ITEM 1

4K039

ITEM 2

4K388

ITEM 3

528933

ITEM 8

528934

ITEM 4

528938

Summary of Contents for Brillion SL10













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands