manualshive.com logo in svg

Landoll Brillion SL10, Operator'S Manual

Share
Download
Landoll Brillion SL10 Operator'S Manual Download Page 46

3-2

1P342-0621

OPERATION

Tractor Preparation

The Turfmaker - Alfalfa Seeder is available as a 
Pull-Type or 3-PT mounted version. 
A Pull-Type seeder is equipped to be pulled by a tractor 
with a drawbar, no clevis.
A 3-PT mounted seeder is compatible with CAT 2 Free 
Link, CAT 2 Quick Coupler and CAT 3 Narrow Quick 
Coupler. 

Tractor Preparation/Attaching of 

3-PT Hitch Seeder

1. Brillion 8, 10, and 12 Foot 3-PT Seeders are 

designed to be pulled with Category 2 Free Link and 
Category 2 or 3N Quick Coupler 3-PT Hitches. 

See 

Figure 3-1.

 Be sure Tractor's Hitch Capacity is not 

exceeded by the Laden Mass of the Seeder. 

Refer 

to Tractor Operator's Manual.

2. Be sure Tractor is properly ballasted. A minimum 

25% of Tractor and Equipment Laden Mass must be 
on Tractor Front Wheels in transport position to 
maintain stability. Calculate the Loaded Seeder 
Mass. 

See “Specifications” on Page 5-1.

 (Seeder 

weight plus the seed box capacity with desired seed.) 

Refer to Tractor Operator's Manual.

3. Check the Tractor tire inflation levels to ensure that 

they are properly inflated for the additional Laden 
Seeder Mass. Refer to the Tractor Operator's 
Manual. Be sure not to over ballast and exceed 
Tractor Tire Capacity.

4. Set Tractor 3-PT Lower Links to allow lateral 

(torsional) float. 

Refer to Tractor Operator's 

Manual.

 If left rigid, your Brillion Seeder may not 

follow ground contours resulting in a poor 
germination.

5. Set Lift Rod length long enough to ensure Seeder 

can float downward in the case of a furrow or 
waterway. Lower Links should be the same height, 
leveling your Brillion Seeder side to side. Fine 
adjustments may need to be made after hookup is 
completed. 

Refer to the Tractor Operator's 

Manual.

6. Attach Seeder to the Tractor's 3-PT Free Link or 

Quick Coupler using the appropriate size pins and 
bushings. Be sure to use the hardware provided and 
is in good working order. 

See Figure 3-1.

 

7. Refer to the Tractor Operator's Manual for Quick 

Hitch Operation. 

DANGER

8. Connect 7-Pin Connector to Tractor Outlet, routing 

cable by avoiding pinch points. 
• Make sure the tractor has a good clean receptacle, 

free of dirt and corrosion.

• Make sure the 7-Pin Connector is inserted ALL the 

way in. With tighter fitting pins, operator may think 
the Connector is all the way in, but really isn’t. 

• Make sure the tractor receptacle cover latches over 

the keyway on the 7-Pin Connector to hold the 
Connector in place. 

• If an operator plugs in the 7-Pin Connector, but the 

lights do not seem to work right, check the above 
items to make sure there is a good connection with 
the 7-Pin Connector.

9. Install Clutch Switch and Harness to tractor if 

Applicable. 

See

 

“Seed Shaft Sensor Kit - 

Optional” on Page 2-16.

 

10. Raise seeder. Remove parking pin. 

See Figure 3-3. 

Adjust or lock tractor sway stabilizers if equipped, 
centering the Seeder with the Tractor. 

Refer to the 

Tractor Operator's Manual. 

11. Lower Seeder, if necessary level Seeder side to side 

(laterally) by adjusting Lift Rod length. Level Seeder 
front to back by adjusting the Tractor Upper Link 
length as required. 

Refer to the Tractor Operator’s 

Manual. 

Do not allow any bystanders to stand between 
the tractor and the machine while backing up to 
the machine.

Summary of Contents for Brillion SL10













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands