manualshive.com logo in svg

Landoll Brillion SL10, Operator'S Manual

Share
Download
Landoll Brillion SL10 Operator'S Manual Download Page 54

3-10

1P342-0621

OPERATION

Transmission Drive Bolt

NOTE

#550 Chain connects Front Roller #550 Chain 6 Tooth 
Sprocket with Transmission #550 Chain 13 Tooth 
Sprocket.

Transmission Drive Bolt (1/4-20 x 2-1/4) from the #550 
Chain 13 Tooth Sprocket, must be removed for 
Calibration and can also be removed if it is desired to 
use the Seeder as a Pulverizer, Rollers only. (The Acre 
Meter will not register when the Bolt is removed).

 See 

Figure 3-12.

Figure 3-12:  Transmission Drive Bolt

Calibration for Unlisted Seeds

Brillion/Landoll assumes no liability pertaining to Seeding 
Rates achieved with this Seeder. Rates listed are general 
in nature and should be used as starting points only. 
Seed varieties and blends listed represent those 
calibrated through in-house test meters.    
Variations in actual rates may be realized due to 
differences in Seed Lots.

 For accurate rates with seeds 

being used, follow the Calibration Instructions listed 
on the Seed Chart inside the Seed Box Cover

.

NOTE

The information listed in the Seed Charts is subject to 
change without notice.

IMPORTANT

Rates are for the 13 Tooth Driver. Double these 
values for the 26 Tooth Driver. See Figure 3-11.
Front Seed Box may be Calibrated for Unlisted Seed 
as follows.

1. Remove Transmission Drive Bolt (1/4-20 x 2-1/4) 

from the #550 Chain 6 Tooth Sprocket. 

See 

Figure 3-12.

2. Raise Seeder and install Transport Locks. 

See 

Figure 3-5.

3. Close Rear Seed Box openings if they contain Seed.
4. Place a Canvas or Tarp under the Machine to catch 

Seed.

5. Turn 15/16 Hex on Transmission Shaft 

Clockwise(CW). 

See Figure 3-13.

8FT Seeder:

 Use 136 turns if you follow Step 6. 

Reference, the Seed Shaft rotates 1,360 Revolutions 
per Acre Seeded with 13 Tooth Driver.

10FT Seeder:

 Use 109 turns if you follow Step 6.

Reference, the Seed Shaft rotates 1,090 Revolutions 
per Acre Seeded with 13 Tooth Driver.

12FT Seeder

: Use 91 turns if you follow Step 6.

 Reference, the Seed Shaft rotates 910 Revolutions 
per Acre Seeded with 13 Tooth Driver.

6. Weigh Seed (lbs) and Multiply by 10 (20 for 26 Tooth 

Driver) for approximate Planting Rate in Pounds per 
Acre.

#550 Chain

19 Tooth Sprocket

#550 Chain

#550 Chain

6 Tooth Sprocket

Drive Bolt,

1/4-20 x 2-1/4

Transmission

Front Roller

Summary of Contents for Brillion SL10













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands