Landoll 2511 IN-3-30 2511 N-4-30 2511 N-5-30, Operator'S Manual

Page: 30 / 60

3-2 F-1040-0123
ASSEMBLY INSTRUCTIONS
TABLE OF CONTENTS
Assembly Preparation
1. Hook up the In-Row Ripper to a tractor using the
3-PT Hitch.
2. Raise the unit about 36" and place stands under the
main frame to prevent accidental lowering.

WARNING
Jack Stand Installation
NOTE
The implement Jack Stand Weldments must be stored
"off the machine" for all
folding machines during
transport and field operation. This is true for both Front
and Rear Jack Stands.
Front Jack Stands - W/ Mount Bracket
1. With the Jack Stand Weldment Bracket positioned on
the bottom side of the front Frame, (clamp facing
out), attach the Jack Mount Bracket to the top using
3/4-10 x 2-1/4 Bolts, 3/4 Flat Washer and 3/4-10
Locknut.
2. Insert the Jack Stand Weldment into the Jack Stand
Weldment Bracket with the handle facing out and pin
at desired level (top five holes), with 3/4 x 4 Hitch Pin
and Hair Pin.
( See Figure 3-1 .)
3. For Rigid Frame transport , remove the Jack Stand
Hitch Pin, and raise the Jack Stand Weldment up
and re-pin through bottom hole.
For Folding Frame
transport , remove the Jack Stand Weldment and
store "off the machine."
Front Jack Stands - W/ Wing Rest
Weldment
1. With the Jack Stand Weldment Bracket positioned on
the bottom side of the front Frame, (clamp facing
out), attach the appropriate Wing-Rest Weldment
using 3/4-10 x 2 Bolts, 3/4 Flat Washer and 3/4-10
Locknut. (The Wing-Rest Weldments have right hand
and left hand designations. The left hand Wing-Rest
Plate Stops slope down toward the left and the right
hand Wing-Rest Plate Stops slope down toward the
right. See Parts Manual for Wing-Rest Weldments
according to model number.)
( See Figure 3-1 .)
2. Insert the Jack Stand Weldment through the bottom
of the Jack Stand Weldment Bracket with the handle
facing out and pin at desired level (top five holes),
with 3/4 x 4 Hitch Pin and Hair Pin.
3. For transport, remove the jack stand Hitch Pin, and
store the Jack Stand Weldment "off the machine."
Rear Jack Stands (Rigid and Folding)
1. With the Jack Stand Mount Bracket positioned on the
bottom side of the rear Frame, attach the Jack Stand
Weldment Bracket (with the clamp facing out
rear-ward), using 1-8 x 3 Bolts, 1" Flat Washers and
1-8 Locknuts.
( See Figure 3-2 .)
2. Insert the Jack Stand Weldment into the Jack Stand
Weldment Bracket and secure with the 1 x 6 Pin and
1/4 x 1-1/4 Lynch Pin.
3. For transport, remove the Jack Stand Lynch Pin and
store the Jack Stand Weldment "off the machine."
Figure 3-1: Front Jack Stand
Figure 3-2: Rear Jack Stand
Do not attempt to lift heavy parts (such as the
frame), manually. Use a hoist or a forklift to move
these parts into position.
FRAME
JACK
STAND
WELDMENT
FRONT
JACK STAND
WELDMENT BRACKET
JACK STAND
MOUNT BRACKET
HITCH PIN
WING-REST
WELDMENT
LEVEL
OPTIONS
PIN,1 X 6
BOLT,
1-8 X 3
JACK STAND
WELDMENT
JACK STAND
MOUNT
BRACKET
LYNCH PIN
JACK STAND
WELDMENT BRACKET
REAR
LOCKNUT,1-8
FLAT WASHER,1"
FLAT
WASHER,1"